Low-Cost, 2-Channel, 짹14-Bit Serial ADCs

General Description The MAX110/MAX111 analog-to-digital converters (ADCs) use an internal auto-calibration technique to achieve 14-bit resolution plus overrange, with no external components. Operating supply current is only 550µA (MAX110) and reduces to 4µA in power-down mode, making these ADCs i

低成本、2通道、±14位串行ADC

MAX110/MAX111模数转换器(ADC)使用内部自动校准技术，无需外部元件即可实现14位分辨率和超量程。这些ADC的工作电源电流仅为550µA (MAX110)，在关断模式下降至4µA，非常适用于高分辨率电池供电或远程检测应用。快速串行接口简化了信号路由和光隔离，节省了微控制器引脚，并提供与SPI™、QSPI™和MICROWIRE™的兼容性。MAX110采用±5V电源供电，可转换-3V至+3V范围内的差分模拟信号。MAX111采用+5V单电源供电，可转换±1.5V范围内的差分模拟信号，或0V至+1.5V范围内的单端信号。\n\n 内部校准功能支持在微处理器(µP)控制下进行失调 • +5V单电源(MAX111)\n\n• 两个差分输入通道\n\n• 14位分辨率加符号和超量程\n\n• 0.03%线性度(MAX110)\n0.05%线性度(MAX111)\n\n• 低功耗：\n\n• 550µA (MAX110)\n\n• 640µA (MAX111)\n\n• 关断电流：4µA\n\n\n\n\n• 每秒高达50次转换\n\n• 50Hz/60Hz抑制\n\n• 自动校准模式\n\n• 无需外部元件\n\n• 16引脚DIP/SO、20引脚SSOP封装;

Convenient Test Points Provided On-Board

文件：685.08 Kbytes Page：19 Pages

Single-Chip, 8-Bit CCD Digitizer with Clamp and 6-Bit PGA

General Description The MAX1101 is a highly integrated IC designed primarily for digitizing the output of a linear CCD array. It provides the components required for all necessary analog functions, including clamp circuitry for black level correction or correlated double sampling (CDS), a three-i

Automatic RF MESFET Amplifier Drain-Current Controllers

General Description The MAX11014/MAX11015 set and control bias conditions for dual MESFET power devices found in point-topoint communication and other microwave base stations. The MAX11014 integrates complete dual analog closed-loop drain-current controllers for Class A MESFET amplifier operation

RF MESFET放大器漏极电流自动控制器

MAX11014/MAX11015设置和控制双路MESFET功率器件的偏置状态，用于点对点通信或其他微波基站。MAX11014集成有两路完整的闭环模拟漏极电流控制器，用于工作在A类放大器的MESFET，而MAX11015针对AB类工作。这两种器件都集成有SRAM查找表(LUT)，用于保存温度和漏极电流补偿数据。\n 每种器件都包含两个高边电流监测放大器，以监测MESFET的漏极电流在取样电阻上的压降，其范围为0至625mV。外部采用二极管连接的晶体管用于监测MESFET的温度，内部温度传感器监测MAX11014/MAX11015管芯的本地温度。内部DAC通过控制栅极电压来设置电流取样电阻上的压 \n• 双通道漏极电流检测放大器 \n• 预设增益为4 \n• 在75mV至625mV检测电压范围内精度为±0.5% (MAX11014) \n• 取样电阻共模电压范围 \n• 0.5V至11V (MAX11014) \n• 5V至32V (MAX11015) \n• 低噪声栅极偏置输出，具备±10mA栅极驱动能力 \n• 快速嵌位和上电复位 \n• 12位DAC控制MESFET栅极电压 \n• 内部温度传感器/双通道外部温度传感器 \n• 内部12位ADC测量温度和电压 \n• 可通过引脚选择串行接口 \n• 3.4MHz I²C兼容接口 \n• 20MHz SPI/MICROWIR;

Automatic RF MESFET Amplifier Drain-Current Controllers

General Description The MAX11014/MAX11015 set and control bias conditions for dual MESFET power devices found in point-topoint communication and other microwave base stations. The MAX11014 integrates complete dual analog closed-loop drain-current controllers for Class A MESFET amplifier operation

Automatic RF MESFET Amplifier Drain-Current Controllers

General Description The MAX11014/MAX11015 set and control bias conditions for dual MESFET power devices found in point-topoint communication and other microwave base stations. The MAX11014 integrates complete dual analog closed-loop drain-current controllers for Class A MESFET amplifier operation

RF MESFET放大器漏极电流自动控制器

MAX11014/MAX11015设置和控制双路MESFET功率器件的偏置状态，用于点对点通信或其他微波基站。MAX11014集成有两路完整的闭环模拟漏极电流控制器，用于工作在A类放大器的MESFET，而MAX11015针对AB类工作。这两种器件都集成有SRAM查找表(LUT)，用于保存温度和漏极电流补偿数据。\n 每种器件都包含两个高边电流监测放大器，以监测MESFET的漏极电流在取样电阻上的压降，其范围为0至625mV。外部采用二极管连接的晶体管用于监测MESFET的温度，内部温度传感器监测MAX11014/MAX11015管芯的本地温度。内部DAC通过控制栅极电压来设置电流取样电阻上的压 \n• 双通道漏极电流检测放大器 \n• 预设增益为4 \n• 在75mV至625mV检测电压范围内精度为±0.5% (MAX11014) \n• 取样电阻共模电压范围 \n• 0.5V至11V (MAX11014) \n• 5V至32V (MAX11015) \n• 低噪声栅极偏置输出，具备±10mA栅极驱动能力 \n• 快速嵌位和上电复位 \n• 12位DAC控制MESFET栅极电压 \n• 内部温度传感器/双通道外部温度传感器 \n• 内部12位ADC测量温度和电压 \n• 可通过引脚选择串行接口 \n• 3.4MHz I²C兼容接口 \n• 20MHz SPI/MICROWIR;

Automatic RF MESFET Amplifier Drain-Current Controllers

General Description The MAX11014/MAX11015 set and control bias conditions for dual MESFET power devices found in point-topoint communication and other microwave base stations. The MAX11014 integrates complete dual analog closed-loop drain-current controllers for Class A MESFET amplifier operation

Single-Chip, 8-Bit CCD Digitizer with Clamp and 6-Bit PGA

General Description The MAX1101 is a highly integrated IC designed primarily for digitizing the output of a linear CCD array. It provides the components required for all necessary analog functions, including clamp circuitry for black level correction or correlated double sampling (CDS), a three-i

8-Bit CODECs

General Description The MAX1102/MAX1103/MAX1104 CODECs provide both an 8-bit analog-to-digital converter (ADC) and an 8-bit digital-to-analog converter (DAC) with a 4-wire logic interface. The MAX1102/MAX1103 include an onboard +2V/+4V reference, providing a well-regulated, low noise reference fo

8-Bit CODECs

General Description The MAX1102/MAX1103/MAX1104 CODECs provide both an 8-bit analog-to-digital converter (ADC) and an 8-bit digital-to-analog converter (DAC) with a 4-wire logic interface. The MAX1102/MAX1103 include an onboard +2V/+4V reference, providing a well-regulated, low noise reference fo

8-Bit CODECs

General Description The MAX1102/MAX1103/MAX1104 CODECs provide both an 8-bit analog-to-digital converter (ADC) and an 8-bit digital-to-analog converter (DAC) with a 4-wire logic interface. The MAX1102/MAX1103 include an onboard +2V/+4V reference, providing a well-regulated, low noise reference fo

8-Bit CODECs

General Description The MAX1102/MAX1103/MAX1104 CODECs provide both an 8-bit analog-to-digital converter (ADC) and an 8-bit digital-to-analog converter (DAC) with a 4-wire logic interface. The MAX1102/MAX1103 include an onboard +2V/+4V reference, providing a well-regulated, low noise reference fo

8-Bit CODECs

General Description The MAX1102/MAX1103/MAX1104 CODECs provide both an 8-bit analog-to-digital converter (ADC) and an 8-bit digital-to-analog converter (DAC) with a 4-wire logic interface. The MAX1102/MAX1103 include an onboard +2V/+4V reference, providing a well-regulated, low noise reference fo

8-Bit CODECs

General Description The MAX1102/MAX1103/MAX1104 CODECs provide both an 8-bit analog-to-digital converter (ADC) and an 8-bit digital-to-analog converter (DAC) with a 4-wire logic interface. The MAX1102/MAX1103 include an onboard +2V/+4V reference, providing a well-regulated, low noise reference fo

24-Bit, 4-Channel, Simultaneous-Sampling, Cascadable, Sigma-Delta ADC

General Description The MAX11040 is a 24-bit, 4-channel, simultaneous sampling, sigma-delta analog-to-digital converter (ADC). The device allows simultaneous sampling of as many as 32 channels using a built-in cascade feature to synchronize as many as eight devices. The serial interface of the MA

24-Bit, 4-Channel, Simultaneous-Sampling, Cascadable, Sigma-Delta ADC

General Description The MAX11040 is a 24-bit, 4-channel, simultaneous sampling, sigma-delta analog-to-digital converter (ADC). The device allows simultaneous sampling of as many as 32 channels using a built-in cascade feature to synchronize as many as eight devices. The serial interface of the MA

24-/16-Bit, 4-Channel, Simultaneous-Sampling, Cascadable, Sigma-Delta ADCs

General Description The MAX11040K/MAX11060 are 24-/16-bit, 4-channel, simultaneous-sampling, sigma-delta analog-to-digital converters (ADCs). The devices allow simultaneous sampling of as many as 32 channels using a built-in cascade feature to synchronize as many as eight devices. The serial inte

24-/16-Bit, 4-Channel, Simultaneous-Sampling, Cascadable, Sigma-Delta ADCs

General Description The MAX11040K/MAX11060 are 24-/16-bit, 4-channel, simultaneous-sampling, sigma-delta analog-to-digital converters (ADCs). The devices allow simultaneous sampling of as many as 32 channels using a built-in cascade feature to synchronize as many as eight devices. The serial inte

Wired Remote Controllers

General Description The MAX11041/MAX11042 wired remote controllers convert up to six or 30 different pushbuttons into an I2C register. Together with low-cost pushbutton switches and 1 resistors, the MAX11041/MAX11042 are total solutions over a single-wire interface. A wired remote controller easi

Wired Remote Controllers

General Description The MAX11041/MAX11042 wired remote controllers convert up to six or 30 different pushbuttons into an I2C register. Together with low-cost pushbutton switches and 1 resistors, the MAX11041/MAX11042 are total solutions over a single-wire interface. A wired remote controller easi

Wired Remote Controllers

General Description The MAX11041/MAX11042 wired remote controllers convert up to six or 30 different pushbuttons into an I2C register. Together with low-cost pushbutton switches and 1 resistors, the MAX11041/MAX11042 are total solutions over a single-wire interface. A wired remote controller easi

4-/6-/8-Channel, 16-Bit, Simultaneous-Sampling ADCs

General Description The MAX11044/MAX11044B/MAX11045/MAX11045B/MAX11046/MAX11046B 16-bit and MAX11054/MAX11055/MAX11056 14-bit ADCs offer 4, 6, or 8 independent input channels. Featuring independent track and hold (T/H) and SAR circuitry, these parts provide simultaneous sampling at 250ksps for ea

4-/6-/8-Channel, 16-Bit, Simultaneous-Sampling ADCs

General Description The MAX11044/MAX11044B/MAX11045/MAX11045B/MAX11046/MAX11046B 16-bit and MAX11054/MAX11055/MAX11056 14-bit ADCs offer 4, 6, or 8 independent input channels. Featuring independent track and hold (T/H) and SAR circuitry, these parts provide simultaneous sampling at 250ksps for ea

4-/6-/8-Channel, 16-Bit, Simultaneous-Sampling ADCs

General Description The MAX11044/MAX11044B/MAX11045/MAX11045B/MAX11046/MAX11046B 16-bit and MAX11054/MAX11055/MAX11056 14-bit ADCs offer 4, 6, or 8 independent input channels. Featuring independent track and hold (T/H) and SAR circuitry, these parts provide simultaneous sampling at 250ksps for ea

4-/6-/8-Channel, 16-Bit, Simultaneous-Sampling ADCs

General Description The MAX11044/MAX11044B/MAX11045/MAX11045B/MAX11046/MAX11046B 16-bit and MAX11054/MAX11055/MAX11056 14-bit ADCs offer 4, 6, or 8 independent input channels. Featuring independent track and hold (T/H) and SAR circuitry, these parts provide simultaneous sampling at 250ksps for ea

4-/6-/8-Channel, 16-Bit, Simultaneous-Sampling ADCs

General Description The MAX11044/MAX11044B/MAX11045/MAX11045B/MAX11046/MAX11046B 16-bit and MAX11054/MAX11055/MAX11056 14-bit ADCs offer 4, 6, or 8 independent input channels. Featuring independent track and hold (T/H) and SAR circuitry, these parts provide simultaneous sampling at 250ksps for ea

8-Channel Simultaneous- Sampling Analog Front End

General Description The MAX11044/MAX11044B/MAX11045/MAX11045B/MAX11046/MAX11046B 16-bit and MAX11054/MAX11055/MAX11056 14-bit ADCs offer 4, 6, or 8 independent input channels. Featuring independent track and hold (T/H) and SAR circuitry, these parts provide simultaneous sampling at 250ksps for ea

4-/6-/8-Channel, 16-Bit, Simultaneous-Sampling ADCs

General Description The MAX11044/MAX11044B/MAX11045/MAX11045B/MAX11046/MAX11046B 16-bit and MAX11054/MAX11055/MAX11056 14-bit ADCs offer 4, 6, or 8 independent input channels. Featuring independent track and hold (T/H) and SAR circuitry, these parts provide simultaneous sampling at 250ksps for ea

4-/6-/8-Channel, 16-Bit, Simultaneous-Sampling ADCs

The MAX11047 / MAX11048 / MAX11049 16-bit ADCs offer 4, 6, or 8 independent input channels. Featuring independent track and hold (T/H) and SAR circuitry, these parts provide simultaneous sampling at 250ksps for each channel.

4-/6-/8-Channel, 16-Bit, Simultaneous-Sampling ADCs

The MAX11047 / MAX11048 / MAX11049 16-bit ADCs offer 4, 6, or 8 independent input channels. Featuring independent track and hold (T/H) and SAR circuitry, these parts provide simultaneous sampling at 250ksps for each channel.

4-/6-/8-Channel, 16-Bit, Simultaneous-Sampling ADCs

The MAX11047 / MAX11048 / MAX11049 16-bit ADCs offer 4, 6, or 8 independent input channels. Featuring independent track and hold (T/H) and SAR circuitry, these parts provide simultaneous sampling at 250ksps for each channel.

4-/6-/8-Channel, 16-Bit, Simultaneous-Sampling ADCs

The MAX11047 / MAX11048 / MAX11049 16-bit ADCs offer 4, 6, or 8 independent input channels. Featuring independent track and hold (T/H) and SAR circuitry, these parts provide simultaneous sampling at 250ksps for each channel.

4-/6-/8-Channel, 16-Bit, Simultaneous-Sampling ADCs

The MAX11047 / MAX11048 / MAX11049 16-bit ADCs offer 4, 6, or 8 independent input channels. Featuring independent track and hold (T/H) and SAR circuitry, these parts provide simultaneous sampling at 250ksps for each channel.

4-/6-/8-Channel, 16-Bit, Simultaneous-Sampling ADCs

The MAX11047 / MAX11048 / MAX11049 16-bit ADCs offer 4, 6, or 8 independent input channels. Featuring independent track and hold (T/H) and SAR circuitry, these parts provide simultaneous sampling at 250ksps for each channel.

8-Bit CODECs

General Description The MAX1102/MAX1103/MAX1104 CODECs provide both an 8-bit analog-to-digital converter (ADC) and an 8-bit digital-to-analog converter (DAC) with a 4-wire logic interface. The MAX1102/MAX1103 include an onboard +2V/+4V reference, providing a well-regulated, low noise reference fo

Single-Supply, Low-Power, Serial 8-Bit ADCs

General Description The MAX1106/MAX1107 low-power, 8-bit, single-channel, analog-to-digital converters (ADCs) feature an internal track/hold (T/H), voltage reference, clock, and serial interface. The MAX1106 is specified from +2.7V to +3.6V and consumes only 96µA. The MAX1107 is specified from +4

24-/16-Bit, 4-Channel, Simultaneous-Sampling, Cascadable, Sigma-Delta ADCs

General Description The MAX11040K/MAX11060 are 24-/16-bit, 4-channel, simultaneous-sampling, sigma-delta analog-to-digital converters (ADCs). The devices allow simultaneous sampling of as many as 32 channels using a built-in cascade feature to synchronize as many as eight devices. The serial inte

Single-Supply, Low-Power, Serial 8-Bit ADCs

General Description The MAX1106/MAX1107 low-power, 8-bit, single-channel, analog-to-digital converters (ADCs) feature an internal track/hold (T/H), voltage reference, clock, and serial interface. The MAX1106 is specified from +2.7V to +3.6V and consumes only 96µA. The MAX1107 is specified from +4

Single-Supply, Low-Power, Serial 8-Bit ADCs

General Description The MAX1106/MAX1107 low-power, 8-bit, single-channel, analog-to-digital converters (ADCs) feature an internal track/hold (T/H), voltage reference, clock, and serial interface. The MAX1106 is specified from +2.7V to +3.6V and consumes only 96µA. The MAX1107 is specified from +4

Single-Supply, Low-Power, Serial 8-Bit ADCs

General Description The MAX1106/MAX1107 low-power, 8-bit, single-channel, analog-to-digital converters (ADCs) feature an internal track/hold (T/H), voltage reference, clock, and serial interface. The MAX1106 is specified from +2.7V to +3.6V and consumes only 96µA. The MAX1107 is specified from +4

Single-Supply, Low-Power, Serial 8-Bit ADCs

General Description The MAX1106/MAX1107 low-power, 8-bit, single-channel, analog-to-digital converters (ADCs) feature an internal track/hold (T/H), voltage reference, clock, and serial interface. The MAX1106 is specified from +2.7V to +3.6V and consumes only 96µA. The MAX1107 is specified from +4

Single-Supply, Low-Power, Serial 8-Bit ADCs

General Description The MAX1106/MAX1107 low-power, 8-bit, single-channel, analog-to-digital converters (ADCs) feature an internal track/hold (T/H), voltage reference, clock, and serial interface. The MAX1106 is specified from +2.7V to +3.6V and consumes only 96µA. The MAX1107 is specified from +4

Single-Supply, Low-Power, Serial 8-Bit ADCs

General Description The MAX1106/MAX1107 low-power, 8-bit, single-channel, analog-to-digital converters (ADCs) feature an internal track/hold (T/H), voltage reference, clock, and serial interface. The MAX1106 is specified from +2.7V to +3.6V and consumes only 96µA. The MAX1107 is specified from +4

Single-Supply, Low-Power, 2-Channel, Serial 8-Bit ADCs

General Description The MAX1108/MAX1109 low-power, 8-bit, dual-channel, analog-to-digital converters (ADCs) feature an internal track/hold (T/H) voltage reference, clock, and serial interface. The MAX1108 is specified from +2.7V to +3.6V and consumes only 105µA. The MAX1109 is specified from +4

12-Channel, High-Voltage Battery-Pack Fault Monitor

General Description The MAX11080/MAX11081 are battery-pack fault-monitor ICs capable of monitoring up to 12 lithium-ion (Li+) battery cells. This device is designed to provide an overvoltage or undervoltage fault indication when any of the cells cross the user-selectable threshold for longer than

12-Channel, High-Voltage Battery-Pack Fault Monitor

General Description The MAX11080/MAX11081 are battery-pack fault-monitor ICs capable of monitoring up to 12 lithium-ion (Li+) battery cells. This device is designed to provide an overvoltage or undervoltage fault indication when any of the cells cross the user-selectable threshold for longer than

12-Channel, High-Voltage Battery-Pack Fault Monitor

General Description The MAX11080/MAX11081 are battery-pack fault-monitor ICs capable of monitoring up to 12 lithium-ion (Li+) battery cells. This device is designed to provide an overvoltage or undervoltage fault indication when any of the cells cross the user-selectable threshold for longer than

12-Channel, High-Voltage Battery-Pack Fault Monitor

General Description The MAX11080/MAX11081 are battery-pack fault-monitor ICs capable of monitoring up to 12 lithium-ion (Li+) battery cells. This device is designed to provide an overvoltage or undervoltage fault indication when any of the cells cross the user-selectable threshold for longer than

Single-Supply, Low-Power, 2-Channel, Serial 8-Bit ADCs

General Description The MAX1108/MAX1109 low-power, 8-bit, dual-channel, analog-to-digital converters (ADCs) feature an internal track/hold (T/H) voltage reference, clock, and serial interface. The MAX1108 is specified from +2.7V to +3.6V and consumes only 105µA. The MAX1109 is specified from +4

Single-Supply, Low-Power, 2-Channel, Serial 8-Bit ADCs

General Description The MAX1108/MAX1109 low-power, 8-bit, dual-channel, analog-to-digital converters (ADCs) feature an internal track/hold (T/H) voltage reference, clock, and serial interface. The MAX1108 is specified from +2.7V to +3.6V and consumes only 105µA. The MAX1109 is specified from +4

Single-Supply, Low-Power, 2-Channel, Serial 8-Bit ADCs

General Description The MAX1108/MAX1109 low-power, 8-bit, dual-channel, analog-to-digital converters (ADCs) feature an internal track/hold (T/H) voltage reference, clock, and serial interface. The MAX1108 is specified from +2.7V to +3.6V and consumes only 105µA. The MAX1109 is specified from +4

Single-Supply, Low-Power, 2-Channel, Serial 8-Bit ADCs

General Description The MAX1108/MAX1109 low-power, 8-bit, dual-channel, analog-to-digital converters (ADCs) feature an internal track/hold (T/H) voltage reference, clock, and serial interface. The MAX1108 is specified from +2.7V to +3.6V and consumes only 105µA. The MAX1109 is specified from +4

Single-Supply, Low-Power, 2-Channel, Serial 8-Bit ADCs

General Description The MAX1108/MAX1109 low-power, 8-bit, dual-channel, analog-to-digital converters (ADCs) feature an internal track/hold (T/H) voltage reference, clock, and serial interface. The MAX1108 is specified from +2.7V to +3.6V and consumes only 105µA. The MAX1109 is specified from +4

Low-Cost, 2-Channel, 짹14-Bit Serial ADCs

General Description The MAX110/MAX111 analog-to-digital converters (ADCs) use an internal auto-calibration technique to achieve 14-bit resolution plus overrange, with no external components. Operating supply current is only 550µA (MAX110) and reduces to 4µA in power-down mode, making these ADCs i

Low-Cost, 2-Channel, 짹14-Bit Serial ADCs

General Description The MAX110/MAX111 analog-to-digital converters (ADCs) use an internal auto-calibration technique to achieve 14-bit resolution plus overrange, with no external components. Operating supply current is only 550µA (MAX110) and reduces to 4µA in power-down mode, making these ADCs i

Low-Cost, 2-Channel, 짹14-Bit Serial ADCs

General Description The MAX110/MAX111 analog-to-digital converters (ADCs) use an internal auto-calibration technique to achieve 14-bit resolution plus overrange, with no external components. Operating supply current is only 550µA (MAX110) and reduces to 4µA in power-down mode, making these ADCs i

Low-Cost, 2-Channel, 짹14-Bit Serial ADCs

General Description The MAX110/MAX111 analog-to-digital converters (ADCs) use an internal auto-calibration technique to achieve 14-bit resolution plus overrange, with no external components. Operating supply current is only 550µA (MAX110) and reduces to 4µA in power-down mode, making these ADCs i