Serial Output 5.6us 12-Bit A/D Converter

Serial Output 5.6μs 12-Bit A/D Converter Applications Telecomunication Digital Signal Processing (DSP) Sonar/Radar Signal Processing Isolated Industrial Data Acquisition

串行输出、5.6µs、12位ADC，内置电压基准

1-Cell to 3-Cell, High-Power 1A, Low-Noise, Step-Up DC-DC Converters

General Description The MAX1700/MAX1701 are high-efficiency, low-noise, step-up DC-DC converters intended for use in battery powered wireless applications. They use a synchronous-rectified pulse-width-modulation (PWM) boost topology to generate 2.5V to 5.5V outputs from battery inputs such as one

完备的DDR2和DDR3电源管理方案

MAX17000脉宽调制(PWM)控制器可以为笔记本电脑中的DDR、DDR2、DDR3存储器提供完整的电源方案。该器件集成了一路降压控制器、一路可源出/吸收电流的LDO稳压器以及一路基准缓冲器，能够产生VDDQ、VTT和VTTR所需的所有电压。\nVDDQ电压由降压转换器提供，采用Maxim专有的Quick-PWM™控制器。高效、恒定导通时间PWM控制器可轻松支持宽范围的输入/输出电压比(适合低占空比应用)，提供100ns的负载瞬态响应，并保持相对恒定的开关频率。Quick-PWM架构不仅解决了固定频率、电流模式PWM出现的负载瞬态特性差的问题，同时还避免了传统的固定导通、关闭时间PWM方案中 • SMPS稳压器(VDDQ) \n• Quick-PWM具有100ns负载阶跃响应 \n• 输出电压可预设为1.8V或1.5V，或在1.0V至2.5V之间调节 \n• 在整个电源和负载工作范围内保证1%的VOUT精度 \n• 最大输入电压额定值26V \n• 精确的谷电流限制保护 \n• 200kHz至600kHz开关频率 \n• 可源出/吸收电流的线性稳压器(VTT)\n• ±2A源出/吸入电流峰值 \n• 对输出电容要求较低 \n• 输出电压预设为VDDQ/2或通过REFIN在0.5V至1.5V之间调节 \n• 待机状态下具有低静态电流 \n• 软启动/软关断 \n• SMPS电;

完备的DDR2和DDR3存储器电源管理方案

MAX17000A脉宽调制(PWM)控制器为笔记本电脑的DDR、DDR2、DDR3存储器提供完整的电源方案。该器件集成了一路降压控制器、一路可源出/吸入电流的LDO稳压器以及一路基准缓冲器，能够产生VDDQ、VTT和VTTR所需的所有电压。\n\n VDDQ电压由降压转换器提供，采用Maxim专有的Quick-PWM™控制器。高效、固定导通时间PWM控制器可轻松支持宽范围的输入/输出电压比(适合低占空比应用)，提供100ns的负载瞬态响应，并保持相对固定的开关频率。Quick-PWM架构不仅解决了固定频率、电流模式PWM存在的负载瞬态响应较差的问题，同时还避免了传统的固定导通、关闭时 • SMPS稳压器(VDDQ)\n• Quick-PWM具有100ns负载阶跃响应 \n• 输出电压可预设为1.8V或1.5V，或在1.0V至2.5V之间调节\n• 在整个电源和负载工作范围内保证1%的VOUT精度\n• 26V最大输入电压额定值\n• 精确的谷电流限制保护\n• 200kHz至600kHz开关频率\n\n\n• 可源出/吸入电流的线性稳压器(VTT) \n• ±2A源出/吸入电流峰值 \n• 对输出电容要求较低\n• 输出电压预设为VDDQ/2或通过REFIN在0.5V至1.5V之间调节\n\n\n• 软启动/软关断 \n• SMPS电源就绪窗比较器 \n• VTT电;

Complete DDR2 and DDR3 Memory Power-Management Solution

General Description The MAX17000A pulse-width modulation (PWM) controller provides a complete power solution for notebook DDR, DDR2, and DDR3 memory. It comprises a stepdown controller, a source-sink LDO regulator, and a reference buffer to generate the required VDDQ, VTT, and VTTR rails. Featur

Complete DDR2 and DDR3 Memory Power-Management Solution

General Description The MAX17000A pulse-width modulation (PWM) controller provides a complete power solution for notebook DDR, DDR2, and DDR3 memory. It comprises a stepdown controller, a source-sink LDO regulator, and a reference buffer to generate the required VDDQ, VTT, and VTTR rails. Featur

1.2MHz Low-Cost, High-Performance Chargers

General Description The MAX17005/MAX17006/MAX17015 are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecture that significantly reduces component size and cost*. The charger uses a high-side MOSFET with n-channel synchronous rectif

1.2MHz, Low-Cost, High-Performance Chargers

General Description The MAX17005A/MAX17006A/MAX17015A are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecture that significantly reduces component size and cost*. The charger uses a high-side MOSFET with n-channel synchrono

1.2MHz, Low-Cost, High-Performance Chargers

General Description The MAX17005A/MAX17006A/MAX17015A are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecture that significantly reduces component size and cost*. The charger uses a high-side MOSFET with n-channel synchrono

1.2MHz, Low-Cost, High-Performance Chargers

General Description The MAX17005B/MAX17006B/MAX17015B are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecturethat significantly reduces component size and cost*. The charger uses a high-side MOSFET with n-channel synchronou

1.2MHz, Low-Cost, High-Performance Chargers

General Description The MAX17005B/MAX17006B/MAX17015B are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecturethat significantly reduces component size and cost*. The charger uses a high-side MOSFET with n-channel synchronou

丝印代码：17005E；1.2MHz Low-Cost, High-Performance Chargers

General Description The MAX17005/MAX17006/MAX17015 are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecture that significantly reduces component size and cost*. The charger uses a high-side MOSFET with n-channel synchronous rectif

1.2MHz Low-Cost, High-Performance Chargers

General Description The MAX17005/MAX17006/MAX17015 are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecture that significantly reduces component size and cost*. The charger uses a high-side MOSFET with n-channel synchronous rectif

1.2MHz, Low-Cost, High-Performance Chargers

General Description The MAX17005A/MAX17006A/MAX17015A are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecture that significantly reduces component size and cost*. The charger uses a high-side MOSFET with n-channel synchrono

1.2MHz, Low-Cost, High-Performance Chargers

General Description The MAX17005A/MAX17006A/MAX17015A are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecture that significantly reduces component size and cost*. The charger uses a high-side MOSFET with n-channel synchrono

1.2MHz, Low-Cost, High-Performance Chargers

General Description The MAX17005B/MAX17006B/MAX17015B are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecturethat significantly reduces component size and cost*. The charger uses a high-side MOSFET with n-channel synchronou

1.2MHz, Low-Cost, High-Performance Chargers

General Description The MAX17005B/MAX17006B/MAX17015B are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecturethat significantly reduces component size and cost*. The charger uses a high-side MOSFET with n-channel synchronou

丝印代码：17006E；1.2MHz Low-Cost, High-Performance Chargers

General Description The MAX17005/MAX17006/MAX17015 are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecture that significantly reduces component size and cost*. The charger uses a high-side MOSFET with n-channel synchronous rectif

1-Cell to 3-Cell, High-Power 1A, Low-Noise, Step-Up DC-DC Converters

General Description The MAX1700/MAX1701 are high-efficiency, low-noise, step-up DC-DC converters intended for use in battery powered wireless applications. They use a synchronous-rectified pulse-width-modulation (PWM) boost topology to generate 2.5V to 5.5V outputs from battery inputs such as one

1-Cell to 3-Cell, High-Power 1A, Low-Noise, Step-Up DC-DC Converters

General Description The MAX1700/MAX1701 are high-efficiency, low-noise, step-up DC-DC converters intended for use in battery powered wireless applications. They use a synchronous-rectified pulse-width-modulation (PWM) boost topology to generate 2.5V to 5.5V outputs from battery inputs such as one

Internal-Switch Boost Regulator with Integrated High-Voltage Level Shifter and Op Amp

General Description The MAX17010 contains a high-performance step-up switching regulator, a high-speed operational amplifier (op amp), and a high-voltage level-shifting scan driver. The device is optimized for thin-film transistor (TFT) liquid-crystal display (LCD) applications. Features ♦ 1.8

Internal-Switch Boost Regulator with Integrated High-Voltage Level Shifter and Op Amp

General Description The MAX17010 contains a high-performance step-up switching regulator, a high-speed operational amplifier (op amp), and a high-voltage level-shifting scan driver. The device is optimized for thin-film transistor (TFT) liquid-crystal display (LCD) applications. Features ♦ 1.8

Low-Cost Multiple-Output Power Supply for LCD TVs

General Description The MAX17014 multiple-output power-supply controller generates all the supply rails for thin-film transistor (TFT) liquid-crystal display (LCD) panels in TVs and monitors operating from a regulated 12V input. It includes a step-down and a step-up regulator, a positive and a

Low-Cost Multiple-Output Power Supply for LCD TVs

General Description The MAX17014 multiple-output power-supply controller generates all the supply rails for thin-film transistor (TFT) liquid-crystal display (LCD) panels in TVs and monitors operating from a regulated 12V input. It includes a step-down and a step-up regulator, a positive and a

1.2MHz Low-Cost, High-Performance Chargers

General Description The MAX17005/MAX17006/MAX17015 are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecture that significantly reduces component size and cost*. The charger uses a high-side MOSFET with n-channel synchronous rectif

1.2MHz, Low-Cost, High-Performance Chargers

General Description The MAX17005A/MAX17006A/MAX17015A are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecture that significantly reduces component size and cost*. The charger uses a high-side MOSFET with n-channel synchrono

1.2MHz, Low-Cost, High-Performance Chargers

General Description The MAX17005A/MAX17006A/MAX17015A are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecture that significantly reduces component size and cost*. The charger uses a high-side MOSFET with n-channel synchrono

1.2MHz, Low-Cost, High-Performance Chargers

General Description The MAX17005B/MAX17006B/MAX17015B are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecturethat significantly reduces component size and cost*. The charger uses a high-side MOSFET with n-channel synchronou

1.2MHz, Low-Cost, High-Performance Chargers

General Description The MAX17005B/MAX17006B/MAX17015B are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecturethat significantly reduces component size and cost*. The charger uses a high-side MOSFET with n-channel synchronou

丝印代码：17015E；1.2MHz Low-Cost, High-Performance Chargers

General Description The MAX17005/MAX17006/MAX17015 are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecture that significantly reduces component size and cost*. The charger uses a high-side MOSFET with n-channel synchronous rectif

Quad-Output Controller for Low-Power Architecture

General Description The MAX17017 is a quad-output controller for ultra mobile portable computers (UMPCs) that rely on a low power architecture. The MAX17017 provides a compact, low-cost controller capable of providing four independent regulators—a main stage, a 3AP-P internal stepdown, a 5AP-P in

Quad-Output Controller for Low-Power Architecture

General Description The MAX17017 is a quad-output controller for ultra mobile portable computers (UMPCs) that rely on a low power architecture. The MAX17017 provides a compact, low-cost controller capable of providing four independent regulators—a main stage, a 3AP-P internal stepdown, a 5AP-P in

1-Cell to 3-Cell, High-Power 1A, Low-Noise, Step-Up DC-DC Converters

General Description The MAX1700/MAX1701 are high-efficiency, low-noise, step-up DC-DC converters intended for use in battery powered wireless applications. They use a synchronous-rectified pulse-width-modulation (PWM) boost topology to generate 2.5V to 5.5V outputs from battery inputs such as one

Dual Quick-PWM Step-Down Controller with Low-Power LDO, RTC Regulator

General Description The MAX17020 is a dual Quick-PWM™ step-down power-supply (SMPS) controller with synchronous rectification, intended for main 5V/3.3V or I/O 1.5V/1.05V power generation in battery-powered systems. Low side MOSFET sensing provides a simple low-cost, highly efficient current se

Dual Quick-PWM Step-Down Controller with Low-Power LDO, RTC Regulator

General Description The MAX17020 is a dual Quick-PWM™ step-down power-supply (SMPS) controller with synchronous rectification, intended for main 5V/3.3V or I/O 1.5V/1.05V power generation in battery-powered systems. Low side MOSFET sensing provides a simple low-cost, highly efficient current se

Dual-Phase, Quick-PWM Controllers for IMVP-6/IMVP-6.5 CPU Core Power Supplies

General Description The MAX17021/MAX17082/MAX17482 are 2/1-phase interleaved Quick-PWM™ step-down VID power-supply controllers for notebook CPUs. True out-of-phase operation reduces input ripple current requirements and output- voltage ripple, while easing component selection and layout difficult

Dual-Phase, Quick-PWM Controllers for IMVP-6/IMVP-6.5 CPU Core Power Supplies

General Description The MAX17021/MAX17082/MAX17482 are 2/1-phase interleaved Quick-PWM™ step-down VID power-supply controllers for notebook CPUs. True out-of-phase operation reduces input ripple current requirements and output- voltage ripple, while easing component selection and layout difficult

Triple-Output Power-Management IC for Microprocessor-Based Systems

General Description The MAX1702B power-management IC supports ARM Powered® devices such as the Intel® PXA210 and PXA250 microprocessors based on the Intel XScale™ micro-architecture. These devices include PDAs, third generation smart cellular phones, internet appliances, automotive in-dash Telema

Triple-Output Power-Management IC for Microprocessor-Based Systems

General Description The MAX1702B power-management IC supports ARM Powered® devices such as the Intel® PXA210 and PXA250 microprocessors based on the Intel XScale™ micro-architecture. These devices include PDAs, third generation smart cellular phones, internet appliances, automotive in-dash Telema

1/2/3-Phase Quick-PWM IMVP-6.5 VID Controllers

General Description The MAX17030/MAX17036 are 3/2-phase interleaved Quick-PWM™ step-down VID power-supply controllers for IMVP-6.5 notebook CPUs. Two integrated drivers and the option to drive a third phase using an external driver such as the MAX8791 allow for a flexible 3/2-phase configuration

1/2/3-Phase Quick-PWM IMVP-6.5 VID Controllers

General Description The MAX17030/MAX17036 are 3/2-phase interleaved Quick-PWM™ step-down VID power-supply controllers for IMVP-6.5 notebook CPUs. Two integrated drivers and the option to drive a third phase using an external driver such as the MAX8791 allow for a flexible 3/2-phase configuration

1/2/3-Phase Quick-PWM IMVP-6.5 VID Controllers

General Description The MAX17030/MAX17036 are 3/2-phase interleaved Quick-PWM™ step-down VID power-supply controllers for IMVP-6.5 notebook CPUs. Two integrated drivers and the option to drive a third phase using an external driver such as the MAX8791 allow for a flexible 3/2-phase configuration

1/2/3-Phase Quick-PWM IMVP-6.5 VID Controllers

General Description The MAX17030/MAX17036 are 3/2-phase interleaved Quick-PWM™ step-down VID power-supply controllers for IMVP-6.5 notebook CPUs. Two integrated drivers and the option to drive a third phase using an external driver such as the MAX8791 allow for a flexible 3/2-phase configuration

Compact, Low-Cost 1S/2S Fuel Gauges

General Description The MAX17040/MAX17041 are ultra-compact, low-cost, host-side fuel-gauge systems for lithium-ion (Li+) batteries in handheld and portable equipment. The MAX17040 is configured to operate with a single lithium cell and the MAX17041 is configured for a dual-cell 2S pack. Feature

Compact, Low-Cost 1S/2S Fuel Gauges

General Description The MAX17040/MAX17041 are ultra-compact, low-cost, host-side fuel-gauge systems for lithium-ion (Li+) batteries in handheld and portable equipment. The MAX17040 is configured to operate with a single lithium cell and the MAX17041 is configured for a dual-cell 2S pack. Feature

Compact, Low-Cost 1S/2S Fuel Gauges

General Description The MAX17040/MAX17041 are ultra-compact, low-cost, host-side fuel-gauge systems for lithium-ion (Li+) batteries in handheld and portable equipment. The MAX17040 is configured to operate with a single lithium cell and the MAX17041 is configured for a dual-cell 2S pack. Feature

Compact, Low-Cost 1S/2S Fuel Gauges

General Description The MAX17040/MAX17041 are ultra-compact, low-cost, host-side fuel-gauge systems for lithium-ion (Li+) batteries in handheld and portable equipment. The MAX17040 is configured to operate with a single lithium cell and the MAX17041 is configured for a dual-cell 2S pack. Feature

Compact, Low-Cost 1S/2S Fuel Gauges

General Description The MAX17040/MAX17041 are ultra-compact, low-cost, host-side fuel-gauge systems for lithium-ion (Li+) batteries in handheld and portable equipment. The MAX17040 is configured to operate with a single lithium cell and the MAX17041 is configured for a dual-cell 2S pack. Feature

Compact, Low-Cost 1S/2S Fuel Gauges

General Description The MAX17040/MAX17041 are ultra-compact, low-cost, host-side fuel-gauge systems for lithium-ion (Li+) batteries in handheld and portable equipment. The MAX17040 is configured to operate with a single lithium cell and the MAX17041 is configured for a dual-cell 2S pack. Feature

Compact, Low-Cost 1S/2S Fuel Gauges Compact, Low-Cost 1S/2S Fuel Gauges

General Description The MAX17043/MAX17044 are ultra-compact, low-cost, host-side fuel-gauge systems for lithium-ion (Li+) batteries in handheld and portable equipment. The MAX17043 is configured to operate with a single lithium cell and the MAX17044 is configured for a dual-cell 2S pack. Feature

Compact, Low-Cost 1S/2S Fuel Gauges Compact, Low-Cost 1S/2S Fuel Gauges

General Description The MAX17043/MAX17044 are ultra-compact, low-cost, host-side fuel-gauge systems for lithium-ion (Li+) batteries in handheld and portable equipment. The MAX17043 is configured to operate with a single lithium cell and the MAX17044 is configured for a dual-cell 2S pack. Feature

Compact, Low-Cost 1S/2S Fuel Gauges Compact, Low-Cost 1S/2S Fuel Gauges

General Description The MAX17043/MAX17044 are ultra-compact, low-cost, host-side fuel-gauge systems for lithium-ion (Li+) batteries in handheld and portable equipment. The MAX17043 is configured to operate with a single lithium cell and the MAX17044 is configured for a dual-cell 2S pack. Feature

Compact, Low-Cost 1S/2S Fuel Gauges Compact, Low-Cost 1S/2S Fuel Gauges

General Description The MAX17043/MAX17044 are ultra-compact, low-cost, host-side fuel-gauge systems for lithium-ion (Li+) batteries in handheld and portable equipment. The MAX17043 is configured to operate with a single lithium cell and the MAX17044 is configured for a dual-cell 2S pack. Feature

Compact, Low-Cost 1S/2S Fuel Gauges Compact, Low-Cost 1S/2S Fuel Gauges

General Description The MAX17043/MAX17044 are ultra-compact, low-cost, host-side fuel-gauge systems for lithium-ion (Li+) batteries in handheld and portable equipment. The MAX17043 is configured to operate with a single lithium cell and the MAX17044 is configured for a dual-cell 2S pack. Feature

Compact, Low-Cost 1S/2S Fuel Gauges Compact, Low-Cost 1S/2S Fuel Gauges

General Description The MAX17043/MAX17044 are ultra-compact, low-cost, host-side fuel-gauge systems for lithium-ion (Li+) batteries in handheld and portable equipment. The MAX17043 is configured to operate with a single lithium cell and the MAX17044 is configured for a dual-cell 2S pack. Feature

1- to 3-Cell, High-Current, Low-Noise, Step-Up DC-DC Converters with Linear Regulator

General Description The MAX1705/MAX1706 are high-efficiency, low-noise, step-up DC-DC converters with an auxiliary linearregulator output. These devices are intended for use in battery-powered wireless applications. They use a synchronous rectifier pulse-width-modulation (PWM) boost topology to g

1- to 3-Cell, High-Current, Low-Noise, Step-Up DC-DC Converters with Linear Regulator

General Description The MAX1705/MAX1706 are high-efficiency, low-noise, step-up DC-DC converters with an auxiliary linearregulator output. These devices are intended for use in battery-powered wireless applications. They use a synchronous rectifier pulse-width-modulation (PWM) boost topology to g

1- to 3-Cell, High-Current, Low-Noise, Step-Up DC-DC Converters with Linear Regulator

General Description The MAX1705/MAX1706 are high-efficiency, low-noise, step-up DC-DC converters with an auxiliary linearregulator output. These devices are intended for use in battery-powered wireless applications. They use a synchronous rectifier pulse-width-modulation (PWM) boost topology to g

1- to 3-Cell, High-Current, Low-Noise, Step-Up DC-DC Converters with Linear Regulator

General Description The MAX1705/MAX1706 are high-efficiency, low-noise, step-up DC-DC converters with an auxiliary linearregulator output. These devices are intended for use in battery-powered wireless applications. They use a synchronous rectifier pulse-width-modulation (PWM) boost topology to g