USB Power Delivery PHY with Channel Configuration Control

Features
On-chip Microcontroller (OCM) to implement USBPD messaging and DisplayPort related functions
DisplayPort Alternate Mode communication support through USB-PD structured VDM messaging
5V-tolerant CC/VCONN signals
Dead battery detection support
I2C slave mode to support exter

8.1G DisplayPort™ 4-lanes Re-timer

Features  Built-in re-timers - Integrated re-timers (Link training-tunable PHY repeater) for DisplayPort up to HBR3 @ 8.1Gbps - Supports both transparent mode and nontransparent mode (transparent or LTTPR) - Loss compensation to recover up to 27dB channel loss  Integrated AUX pass-through

10G USB 3.1 Re-timer (1-Port)

Features
Built-in re-timer - Integrated re-timer for USB 3.1 1-port (Tx/Rx) up to 10Gbps - Loss compensation to recover up to 23dB channel loss
Protocol awareness for better link power management (LPM) and savings
Reference clock for re-timer - Utilizes a 24MHz reference XTAL or 1.05V

10G Active Mux (1x2) with Integrated Re-timer for USB 3.1

Features
Built-in re-timer - Integrated re-timer for USB 3.1 up to Gen 2 @ 10Gbps - Loss compensation to recover up to 23dB channel loss
Integrated mux - Digital (1x2) mux switches USB signals and preserves enhanced signal output over USB-C connector - Mux control input through I2C comma

USB Type-C™ Crosspoint Switch

Features
High-speed switching up to 6.75Gbps
4-lanes DisplayPort inputs with link speed of 1.62Gbps, 2.7Gbps, 5.4Gbps, and 6.75Gbps
USB 3.1 signal (SSTX and SSRX) with Gen1 (5Gbps) link speed
DisplayPort Alternate Mode (SlimPort®) communication support through USB-PD structured VDM mes

USB Type-C™ Crosspoint Switch

Features
High-speed switching up to 6.75Gbps
USB 3.1 signal (SSTX and SSRX) with Gen1 (5Gbps) link speed
On-chip Microcontroller (OCM) to implement signal switching, USB-PD messaging, and related functions
5V-tolerant CC/VCONN signals
Dead battery detection support
I2C slave mode

USB Power Delivery PHY with Channel Configuration Control

Features
On-chip Microcontroller (OCM) to implement cable detection and USB-PD messaging for charging related functions
5V-tolerant CC/VCONN signals
Dead battery detection support
I2C slave mode to support external MCU/IC
VBUS control and USB_ID pins to control external switch, Powe

10G Active Mux (6x4) with Integrated Re-timers for USB™ 3.1/DisplayPort™

LAN 1000 Base T Dual Port Magnetic Modules

• Designed for Ethernet 100/1000 Base-T full duplex applications • Supports 4 pairs of category 5 UTP cable • Cable interface for isolation and low common mode emissions • Compliant with IEEE 802.3ab standard for 1000 Base-T • Supports 1:1 Turns Ratio Transceivers • Isolation voltag

MachFlex™, 111G C #14 Str BC, PVC-NYL Ins, TPE Jkt, 1000V WTTC,600V TC-ER

Product Description MachFlex™ for High Flex, 11+1G Conductor 14AWG (41x30) Bare Copper, PVC-NYL Insulation, TPE Outer Jacket, 1000V WTTC, 600V TC-ER

Differential Input, 1 MSPS 10-Bit and 12-Bit ADCs in an 8-Lead SOT-23

GENERAL DESCRIPTION The AD7440/AD7450A1 are 10-bit and 12-bit high speed, low power, successive approximation (SAR) analog-to-digital converters with a fully differential analog input. These parts operate from a single 3 V or 5 V power supply and use advanced design techniques to achieve very low

1000 Base T Dual Port Magnetic module

文件：625.76 Kbytes Page：2 Pages

Differential Input, 1 MSPS ADCs in an 8-Lead SOT-23

文件：784.57 Kbytes Page：28 Pages