High-Speed CMOS 10-Bit Bus Switch with Flow-Thru Pinout

The QS3861 provides a set of ten high-speed CMOS TTL-compatible bus switches. The low ON resistance (5 ohm) of the QS3861 allows inputs to be connected without adding propagation delay and without generating additional ground bounce noise. The Bus Enable (BE) signal turns the switches on. The QS3861 Enhanced N channel FET with no inherent diode to Vcc\n5 ohm bidirectional switches connect inputs to outputs\nZero propagation delay, zero ground bounce\nUndershoot clamp diodes on all switch and control inputs\nAvailable in 24 pin QSOP and TSSOP packages;

The QS3861 provides a set of ten high-speed CMOS TTL-compatible bus switches.

文件：43.63 Kbytes Page：5 Pages

QUICKSWITCH® PRODUCTS HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT

FEATURES: • Enhanced N channel FET with no inherent diode to Vcc • 5Ω bidirectional switches connect inputs to outputs • Zero propagation delay, zero ground bounce • Undershoot clamp diodes on all switch and control inputs • Available in QSOP and TSSOP packages APPLICATIONS: • Hot-swapping,

QUICKSWITCH® PRODUCTS HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT

FEATURES: • Enhanced N channel FET with no inherent diode to Vcc • 5Ω bidirectional switches connect inputs to outputs • Zero propagation delay, zero ground bounce • Undershoot clamp diodes on all switch and control inputs • Available in QSOP and TSSOP packages APPLICATIONS: • Hot-swapping,

QUICKSWITCH® PRODUCTS HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT

FEATURES: • Enhanced N channel FET with no inherent diode to Vcc • 5Ω bidirectional switches connect inputs to outputs • Zero propagation delay, zero ground bounce • Undershoot clamp diodes on all switch and control inputs • Available in QSOP and TSSOP packages APPLICATIONS: • Hot-swapping,

QUICKSWITCH® PRODUCTS HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT

FEATURES: • Enhanced N channel FET with no inherent diode to Vcc • 5Ω bidirectional switches connect inputs to outputs • Zero propagation delay, zero ground bounce • Undershoot clamp diodes on all switch and control inputs • Available in QSOP and TSSOP packages APPLICATIONS: • Hot-swapping,

HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH FLOW-THROUGH PINOUT

文件：218.86 Kbytes Page：5 Pages

封装/外壳：24-TSSOP（0.173"，4.40mm 宽） 包装：管件 描述：IC BUS SWITCH 10 X 1:1 24TSSOP 集成电路（IC） 信号开关，多路复用器，解码器

封装/外壳：24-SSOP（0.154"，3.90mm 宽） 包装：卷带（TR）剪切带（CT）Digi-Reel® 得捷定制卷带 描述：IC BUS SWITCH 10 X 1:1 24QSOP 集成电路（IC） 信号开关，多路复用器，解码器

QUICKSWITCH PRODUCTS HIGH-SPEED CMOS 10-BIT BUS SWITCH WITH BUS SWITCH WITH

文件：218.86 Kbytes Page：5 Pages

Sensor-less Motor Drive IC for VTR Movie Cylinder

■ Features • Operating supply voltage range : VCC=3.0 to 5.5V, VB=4.0 to 10.5V • Reduced magnetosound using 3-phase full-wave overlap drive. Built-in power transistor. • Standby mode for minimizing power consumption • Voltage output for controlling SW power supply • Motor neutral point inpu

Direct Sequence Spread Spectrum Baseband Processor

The Intersil HFA3861 Direct Sequence Spread Spectrum (DSSS) baseband processor is part of the PRISM® 2.4GHz radio chipset, and contains all the functions necessary for a full or half duplex packet baseband transceiver. Features • Complete DSSS Baseband Processor • Processing Gain . . . . . . .

Integrated Load Switch

General Description This device is particularly suited for compact power management in portable electronic equipment where 2.5V to 8V input and 2.8A output current capability are needed. This load switch integrates a small N-Channel power MOSFET (Q1) that drives a large P-Channel power MO

Integrated Load Switch

General Description This device is particularly suited for compact power management in portable electronic equipment where 2.5V to 8V input and 2.8A output current capability are needed. This load switch integrates a small N-Channel power MOSFET (Q1) that drives a large P-Channel power MO

10-BIT FET BUS SWITCH

文件：258.529 Kbytes Page：10 Pages