짹60V Fault Protected 3V to 5.5V RS485/RS422 Transceiver with Level 4 IEC ESD

DESCRIPTION TheLTC®2862Ais a low power,20Mbpsor250kbpsRS485/RS422 transceiver operating on 3V to 5.5V supplies with ±60V overvoltage fault protection on the interface pins during all modes of operation, including power-down. Improvements were made to the LTC2862 for greater robustness and signal

±60V Fault Protected 3V to 5.5V RS485/RS422 Transceiver with Level 4 IEC ESD

FEATURES - Protected from Overvoltage Line Faults to ±60V 3V to 5.5V Supply Voltage - 20Mbps or Low EMI 250kbps Data Rate - ±40kV HBM ESD Interface Pins, ±15kV Other Pins - Enhanced Receiver and Failsafe Noise Immunity - IEC Level 4 ESD and EFT on Interface Pins - Extended Common Mode Rang

짹60V Rugged PROFIBUS RS485 Transceivers

文件：1.65321 Mbytes Page：32 Pages

짹60V Fault Protected 3V to 5.5V RS485/RS422 Transceiver with Level 4 IEC ESD

文件：478.68 Kbytes Page：22 Pages

20Mbps RS485 Transceivers

文件：340.25 Kbytes Page：18 Pages

Complete Isolated RS485/RS422 關Module

文件：398.81 Kbytes Page：24 Pages

60V Fault Protected 3V to 5.5V RS485/RS422 Transceivers

文件：386.91 Kbytes Page：26 Pages

封装/外壳：12-WFDFN 裸露焊盘 包装：管件 描述：IC TRANSCEIVER FULL 1/1 12DFN 集成电路（IC） 驱动器，接收器，收发器

封装/外壳：12-TSSOP（0.118"，3.00mm 宽）裸露焊盘 包装：管件 描述：IC TRANSCEIVER FULL 1/1 12MSOP 集成电路（IC） 驱动器，接收器，收发器

Direct-acting 2-way basic proportional valve

Type 2865 is an extremely compact solenoid control valve and is available with an orifice up to 8 mm. It is based on the standard version of Type 2875. It is used as an actuator in closed control loops (pressure, flow, temperature, etc.). Compared with the standard version, the valve is essent

5.7 kV RMS Signal and Power Isolated RS-485 Transceiver with 짹15 kV IEC ESD

GENERAL DESCRIPTION The ADM2861E, ADM2863E, ADM2865E, and ADM2867E are 5.7 kV rms signal and power isolated RS-485 transceivers. These devices are designed for balanced transmission lines and comply with ANSI/TIA/EIA-485-A-98 and ISO 8482:1987(E). The devices pass radiated emissions testing to th

5.7 kV RMS Signal and Power Isolated RS-485 Transceiver with 짹15 kV IEC ESD

GENERAL DESCRIPTION The ADM2861E, ADM2863E, ADM2865E, and ADM2867E are 5.7 kV rms signal and power isolated RS-485 transceivers. These devices are designed for balanced transmission lines and comply with ANSI/TIA/EIA-485-A-98 and ISO 8482:1987(E). The devices pass radiated emissions testing to th

80 MHz bandpass filter

文件：48.91 Kbytes Page：2 Pages

Open/Closed Bushings

文件：128.11 Kbytes Page：1 Pages