GENERAL DESCRIPTION

The W25Q16DV (16M-bit) Serial Flash memory provides a storage solution for systems with limited

space, pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial Flash

devices. They are ideal for code shadowing to RAM, executing code directly from Dual/Quad SPI (XIP)

and storing voice, text and data. The device operates on a single 2.7V to 3.6V power supply with current

consumption as low as 4mA active and 1µA for power-down.

The W25Q16DV array is organized into 8,192 programmable pages of 256-bytes each. Up to 256 bytes

can be programmed at a time. Pages can be erased in groups of 16 (4KB sector erase), groups of 128

(32KB block erase), groups of 256 (64KB block erase) or the entire chip (chip erase). The W25Q16DV

has 512 erasable sectors and 32 erasable blocks respectively. The small 4KB sectors allow for greater

flexibility in applications that require data and parameter storage. (See figure 2.)

The W25Q16DV supports the standard Serial Peripheral Interface (SPI), and a high performance

Dual/Quad output as well as Dual/Quad I/O SPI: Serial Clock, Chip Select, Serial Data I/O0 (DI), I/O1

(DO), I/O2 (/WP), and I/O3 (/HOLD). SPI clock frequencies of up to 104MHz are supported allowing

equivalent clock rates of 208MHz (104MHz x 2) for Dual I/O and 416MHz (104MHz x 4) for Quad I/O when

using the Fast Read Dual/Quad I/O instructions. These transfer rates can outperform standard

Asynchronous 8 and 16-bit Parallel Flash memories. The Continuous Read Mode allows for efficient

memory access with as few as 8-clocks of instruction-overhead to read a 24-bit address, allowing true XIP

(execute in place) operation.

A Hold pin, Write Protect pin and programmable write protection, with top or bottom array control,

provide further control flexibility. Additionally, the device supports JEDEC standard manufacturer and

device identification with a 64-bit Unique Serial Number.

FEATURES

 Family of SpiFlash Memories

– W25Q16DV: 16M-bit / 2M-byte (2,097,152)

– 256-byte per programmable page

– Standard SPI: CLK, /CS, DI, DO, /WP, /Hold

– Dual SPI: CLK, /CS, IO0, IO1, /WP, /Hold

– Quad SPI: CLK, /CS, IO0, IO1, IO2, IO3

 Highest Performance Serial Flash

– 104MHz Dual SPI / Quad SPI clocks

– 208/416MHz equivalent Dual/Quad SPI

– 52MB/S continuous data transfer rate

– Up to 8X that of ordinary Serial Flash

– More than 100,000 erase/program cycles

– More than 20-year data retention

 Efficient “Continuous Read Mode”

– Low Instruction overhead

– Continuous Read with 8/16/32/64-Byte Wrap

– As few as 8 clocks to address memory

– Allows true XIP (execute in place) operation

– Outperforms X16 Parallel Flash

 Low Power, Wide Temperature Range

– Single 2.7 to 3.6V supply

– 4mA active current, <1µA Power-down (typ.)

– -40°C to +85°C operating range

 Flexible Architecture with 4KB sectors

– Uniform Sector/Block Erase (4/32/64K-bytes)

– Program one to 256 bytes

– Erase/Program Suspend & Resume

 Advanced Security & Identification Features

– Software and Hardware Write-Protect

– Top/Bottom, 4KB complement array protection

– Power Supply Lock-Down and OTP protection

– 64-Bit Unique ID for each device

– Discoverable Parameters (SFDP) Register

– 3X256-Byte Security Registers with OTP locks

– Volatile & Non-volatile Status Register Bits

 Space Efficient Packaging(1)

– 8-pin SOIC 150/208-mil

– 8-pad WSON 6x5-mm

– 8-pad USON 4X3mm / 4X4mm

– 8-pin PDIP 300-mil

– 8-ball WLCSP

– 16-pin SOIC 300-mil

– 24-ball TFBGA 8x6-mm (6x4/5x5 ball array)

– Contact Winbond for KGD and other options