UM232H Single Channel USB Hi-Speed FT232H Development Module Datasheet

Introduction The UM232H is a USB-to-serial/FIFO development module in the FTDI product range which utilises the FT232H USB Hi-Speed (480Mb/s) single-port bridge chip to handle the USB signaling and protocols. The UM232H is ideal for development purposes to quickly prove functionality of adding

UM232H - 开发模块, UM232H - FT232H

The UM232H is a USB-to-serial/FIFO development module in the FTDI product range which utilises the FT232H USB Hi-Speed (480Mb/s) single-port bridge chip to handle the USB signalling and protocols. It is ideal for development purposes to quickly prove functionality of adding USB to a target design. T ·Based on the Single chip USB Hi-Speed FT232H device\n·USB 2.0 Hi-Speed (480Mbps) and Full Speed (12Mbps) compatible\n·Entire USB protocol handled on the chip\n·USB bus or self powered options\n·Asynchronous UART transfer data rate up to 12Mbaud\n·UART interface support for 7 or 8 data bits\n·Fully ;

功能：USB 2.0 转串行 FIFO 桥接器 包装：散装 描述：MOD USB HS FT232H EVAL 开发板，套件，编程器 评估和演示板及套件

UM232H-B-NC - 接口模块, USB, 1通道, 3.3V, FT232H

The UM232H-B-NC is a Development Module for FT232H high-speed USB 2.0 to serial/parallel interface connector. The single channel interface IC can be configured to transfer data over UART, FIFO, FT1248, I²C, SPI and GPIO interfaces. The UART signal is available via 8 pads on the PCB. ·Breakout converter board\n·Operate at +3.3V voltage levels\n·5V tolerant I/Os\n·No connector;

UM232H-B-WE - 接口模块, USB, 1通道, 3.3V, FT232H

The UM232H-B-WE is a Development Module for FT232H high-speed USB 2.0 to serial/parallel interface connector. The single channel interface IC can be configured to transfer data over UART, FIFO, FT1248, I²C, SPI and GPIO interfaces. The UART signal is available via 8, 6-inch flying leads connected to ·Breakout converter board\n·Operate at +3.3V voltage levels\n·5V tolerant I/Os;

UM232H-B USB to Serial/Parallel Break-Out Module

文件：573.53 Kbytes Page：16 Pages

功能：USB 2.0 转并口和串口 包装：散装 描述：BRD BRKOUT USB HS FT232H NOCNCTR 开发板，套件，编程器 评估和演示板及套件

VERY HIGHSPEED, ULTRA LOWPOWERCONSUMPTION 5V POWERED RS-232 DRIVERS AND RECEIVERS

Description The ST232A is a 2 driver, 2 receiver device following EIA/TIA-232 and V.28 communication standard. It is particularly suitable for applications where ±12V is not available. The ST232A uses a single 5V power supply and only four external capacitors (0.1µF). Typical applications are i

5V POWERED MULTI-CHANNEL RS-232 DRIVERS AND RECEIVERS

DESCRIPTION The ST232 is a 2 driver, 2 receiver device following EIA/TIA-232 and V.28 communication standard. It is particularly suitable for applications where ±12V is not available. The ST232 uses a single 5V power supply and only four external capacitors (0.1µF). Typical applications are in:

5V POWERED MULTI-CHANNEL RS-232 DRIVERS AND RECEIVERS

DESCRIPTION The ST232 is a 2 driver, 2 receiver device following EIA/TIA-232 and V.28 communication standard. It is particularly suitable for applications where ±12V is not available. The ST232 uses a single 5V power supply and only four external capacitors (0.1µF). Typical applications are in:

5V POWERED MULTI-CHANNEL RS-232 DRIVERS AND RECEIVERS

DESCRIPTION The ST232 is a 2 driver, 2 receiver device following EIA/TIA-232 and V.28 communication standard. It is particularly suitable for applications where ±12V is not available. The ST232 uses a single 5V power supply and only four external capacitors (0.1µF). Typical applications are in:

5V POWERED MULTI-CHANNEL RS-232 DRIVERS AND RECEIVERS

DESCRIPTION The ST232 is a 2 driver, 2 receiver device following EIA/TIA-232 and V.28 communication standard. It is particularly suitable for applications where ±12V is not available. The ST232 uses a single 5V power supply and only four external capacitors (0.1µF). Typical applications are in: