Features

■ 32-bit RX CPU core

 Max. operating frequency: 100 MHz

Capable of 165 DMIPS in operation at 100 MHz

 Single precision 32-bit IEEE-754 floating point

 Two types of multiply-and-accumulation unit (between memories

and between registers)

 32-bit multiplier (fastest instruction execution takes one CPU clock

cycle)

 Divider (fastest instruction execution takes two CPU clock cycles)

 Fast interrupt

 CISC Harvard architecture with 5-stage pipeline

 Variable-length instructions: Ultra-compact code

 Supports the memory protection unit (MPU)

 Two types of debugging interfaces: JTAG and FINE (two-line)

■ Low-power design and architecture

 Single 3.3-V supply or single 5-V supply; 3.3-V products can be

used with a 5-V analog power supply

 Four low-power modes

■ On-chip main flash memory, no wait states

 100-MHz operation, 10-ns read cycle (no wait states)

 Max. 512 Kbytes

 User code is programmable by USB, SCI, or JTAG.

■ On-chip data flash memory

 Max. 32 Kbytes, reprogrammable up to 100,000 times

 Programming/erasing as background operations (BGOs)

■ On-chip SRAM, no wait states

 Max. 48 Kbytes

 For instructions and operands

■ DMA

 DMA: Incorporates four channels

 DTC: A single unit can handle transfer on multiple channels.

■ Reset and supply management

 Power-on reset (POR)

 Low voltage detection (LVD) with voltage settings

■ Clock functions

 External crystal oscillator or internal PLL for operation at 4 to 12.5

MHz

 Internal 125-kHz LOCO

 Dedicated 125-kHz LOCO for the IWDT

■ Independent watchdog timer

 125-kHz LOCO clock operation

■ Useful functions for IEC60730 compliance

 Oscillation-stop detection, frequency measurement, CRC, IWDT,

self-diagnostic function for the A/D converter, etc.

■ External address space

 4 CS areas (4 × 1 Mbyte)

 Multiplexed address data or separate address lines are selectable per

area.

 8- or 16-bit bus space is selectable per area.

■ Up to 11 communications interfaces

 USB 2.0 full-speed function interface (1 channel)

 CAN (compliant with ISO11898-1), incorporating 32 mailboxes (1

channel)

 SCI with multiple functionalities (5 channels)

Choose from among asynchronous mode, clock-synchronous mode,

smart-card interface mode, simple SPI, simple I2C, and extended

serial mode.

 I2C bus interface for SMBus (2 channels)

 RSPI for high-speed transfer (2 channels)

■ Up to twenty 16-bit timers

 16-bit MTU3: 100-MHz operation, input capture, output compare,

three-phase complementary PWM waveform output (2 channels),

phase-counting mode (8 channels); complementary PWM does not

burden the CPU.

 16-bit GPT: 100-MHz operation, input capture, output compare, 4-

channel single-phase complementary PWM waveform output or 1-

channel three-phase complementary + 1-channel single-phase

complementary output, interlocking with comparator (counter

operation, PWM negation control), detection of abnormal oscillation

frequencies (useful for IEC60730 compliance)

(8 channels); complementary PWM does not burden the CPU.

 16-bit CMT (4 channels)

■ Generation of delays in PWM waveforms (for

products with the product ID code 1)

 The timing with which signals on the 16-bit GPT PWM output pin

rise and fall can be controlled with an accuracy of up to 312 ps (in

operation at 100 MHz).

■ Two A/D converters for 1-MHz operation, total of 8

channels

 Simultaneous sampling on 7 channels is possible with three units.

 Self-diagnosis function (useful for IEC60730 compliance)

 Two 12-bit ADCs: three sample-and-hold circuits, double data

registers, amplifier, comparator (8 channels)

 One 10-bit ADC (12 channels)

■ One A/D converter for 2-MHz operation, total of 20

channels

 One 10-bit ADC (20 channels)

■ 10-bit D/A converter: 2 channels

■ Digital Power Supply Controller-Dedicated

Calculation Function (for products with product ID

code 1)

 16-bit fixed-point calculation function that handles compensatory

calculations in the method of digital control for switched-mode

power supplies.

■ Register write protection function can protect values

in important registers against overwriting.

■ Up to 110 pins for GPIO

 Open drain, switchable driving ability

■ Operating temp. range

 –40C to +85C

 –40C to +105C