Features

 High Performance Non-Blocking Switch Architecture

– 32-lane, 24-port PCIe switch with flexible port configuration

– Integrated SerDes supports 5.0 GT/s Gen2 and 2.5 GT/s

Gen1 operation

– Delivers up to 32 GBps (256 Gbps) of switching capacity

– Supports 128 Bytes to 2 KB maximum payload size

– Low latency cut-through architecture

– Supports one virtual channel and eight traffic classes

 Port Configurability

– Four x8 stacks

• Two x8 stacks, each configurable as:

• One x8 port

• Two x4 ports

• Four x2 ports

• Eight x1 ports

• Several combinations of the above lane widths

• Two x8 stacks, each configurable as:

• One x8 port

• Two x4 ports

• Four x2 ports

• Several combinations of the above lane widths

– Automatic per port link width negotiation

(x8  x4 x2  x1)

– Crosslink support

– Automatic lane reversal

– Per lane SerDes configuration

• De-emphasis

• Receive equalization

• Drive strength

 Innovative Switch Partitioning Feature

– Supports up to 8 fully independent switch partitions

– Logically independent switches in the same device

– Configurable downstream port device numbering

– Supports dynamic reconfiguration of switch partitions

• Dynamic port reconfiguration — downstream, upstream,

non-transparent bridge

• Dynamic migration of ports between partitions

• Movable upstream port within and between switch partitions

 Non-Transparent Bridging (NTB) Support

– Supports up to 8 NT endpoints per switch, each endpoint can

communicate with other switch partitions or external PCIe

domains or CPUs

– 6 BARs per NT Endpoint

• Bar address translation

• All BARs support 32/64-bit base and limit address translation

• Two BARs (BAR2 and BAR4) support look-up table based

address translation

– 32 inbound and outbound doorbell registers

– 4 inbound and outbound message registers

– Supports up to 64 masters

– Unlimited number of outstanding transactions

 Multicast

– Compliant with the PCI-SIG multicast

– Supports 64 multicast groups

– Supports multicast across non-transparent port

– Multicast overlay mechanism support

– ECRC regeneration support

 Integrated Direct Memory Access (DMA) Controllers

– Supports up to 2 DMA upstream ports, each with 2 DMA channels

– Supports 32-bit and 64-bit memory-to-memory transfers

• Fly-by translation provides reduced latency and increased

performance over buffered approach

• Supports arbitrary source and destination address alignment

• Supports intra- as well as inter-partition data transfers using

the non-transparent endpoint

– Supports DMA transfers to multicast groups

– Linked list descriptor-based operation

– Flexible addressing modes

• Linear addressing

• Constant addressing

 Quality of Service (QoS)

– Port arbitration

• Round robin

– Request metering

• IDT proprietary feature that balances bandwidth among

switch ports for maximum system throughput

High performance switch core architecture

• Combined Input Output Queued (CIOQ) switch architecture

with large buffers

 Clocking

– Supports 100 MHz and 125 MHz reference clock frequencies

– Flexible port clocking modes

• Common clock

• Non-common clock

• Local port clock with SSC (spread spectrum setting) and port

reference clock input

 Hot-Plug and Hot Swap

– Hot-plug controller on all ports

• Hot-plug supported on all downstream switch ports

– All ports support hot-plug using low-cost external I2

C I/O

expanders

– Configurable presence-detect supports card and cable applications

– GPE output pin for hot-plug event notification

• Enables SCI/SMI generation for legacy operating system

support

– Hot-swap capable I/O

 Power Management

– Supports D0, D3hot and D3 power management states

– Active State Power Management (ASPM)

• Supports L0, L0s, L1, L2/L3 Ready, and L3 link states

• Configurable L0s and L1 entry timers allow performance/

power-savings tuning

– SerDes power savings

• Supports low swing / half-swing SerDes operation

• SerDes associated with unused ports are turned off

• SerDes associated with unused lanes are placed in a low

power state

 Reliability, Availability, and Serviceability (RAS)

– ECRC support

– AER on all ports

– SECDED ECC protection on all internal RAMs

– End-to-end data path parity protection

– Checksum Serial EEPROM content protected

– Ability to generate an interrupt (INTx or MSI) on link up/down

transitions

 Initialization / Configuration

– Supports Root (BIOS, OS, or driver), Serial EEPROM, or

SMBus switch initialization

– Common switch configurations are supported with pin strapping (no external components)

– Supports in-system Serial EEPROM initialization/programming

 On-Die Temperature Sensor

– Range of 0 to 127.5 degrees Celsius

– Three programmable temperature thresholds with over and

under temperature threshold alarms

– Automatic recording of maximum high or minimum low

temperature

 9 General Purpose I/O

 Test and Debug

– Ability to inject AER errors simplifies in system error handling

software validation

– On-chip link activity and status outputs available for several

ports

– Per port link activity and status outputs available using

external I2

C I/O expander for all remaining ports

– Supports IEEE 1149.6 AC JTAG and IEEE 1149.1 JTAG

 Standards and Compatibility

– PCI Express Base Specification 2.1 compliant

– Implements the following optional PCI Express features

• Advanced Error Reporting (AER) on all ports

• End-to-End CRC (ECRC)

• Access Control Services (ACS)

• Device Serial Number Enhanced Capability

• Sub-System ID and Sub-System Vendor ID Capability

• Internal Error Reporting

• Multicast

• VGA and ISA enable

• L0s and L1 ASPM

• ARI

 Power Supplies

– Requires three power supply voltages (1.0V, 2.5V, and 3.3V)

 Packaged in a 23mm x 23mm 484-ball Flip Chip BGA with

1mm ball spacing

Product Description

With Non-Transparent Bridging functionality and innovative Switch

Partitioning feature, the PES32NT24AG2 allows true multi-host or multiprocessor communications in a single device. Integrated DMA controllers enable high-performance system design by off-loading data transfer

operations across memories from the processors. Each lane is capable

of 5 GT/s link speed in both directions and is fully compliant with PCI

Express Base Specification 2.1.

A non-transparent bridge (NTB) is required when two PCI Express

domains need to communicate to each other. The main function of the

NTB block is to initialize and translate addresses and device IDs to

allow data exchange across PCI Express domains. The major functionalities of the NTB block are summarized in Table 1.