DESCRIPTION

The PM4328 High Density T1/E1 Framer with Integrated M13 Multiplexer (TECT3) is a feature-rich device for use in any applications requiring high density link termination over T1 or E1 channelized DS3.

FEATURES

• Integrates 28 T1 framers, 21 E1 framers and a full featured M13 multiplexer with DS3 framer in a single monolithic device for terminating DS3 multiplexed T1 or E1 streams.

• Four fundamental modes of operation:

• Up to 28 T1 streams M13 multiplexed into a serial DS3.

• Up to 21 E1 streams multiplexed into a DS3 following the ITU-T G.747 recommendation. This E1 mode of operation is restricted to using the serial clock and data or H-MVIP system interfaces.

• DS3 M13 Multiplexer with ingress or egress per link monitoring.

• Unchannelized DS3 framer mode for access to the entire DS3 payload.

• Supports transfer of PCM data to/from 1.544MHz and 2.048MHz serial interface system-side devices. Also supports a fractional T1 or E1 system interface with independent ingress/egress Nx64Kb/s rates. Supports a 2.048 MHz system-side interface for T1 mode without external clock gapping.

• Supports 8Mb/s H-MVIP on the system interface for all T1 or E1 links, a separate 8Mb/s H-MVIP system interface for all T1 or E1 CAS channels and a separate 8Mb/s H-MVIP system interface for all T1 or E1 CCS and V5.1/V5.2 channels.

• Supports a byte serial Scaleable Bandwidth Interconnect (SBI) bus interface for high density system side device interconnection of up to 84 T1 streams or 3 DS3 streams.

• Provides jitter attenuation in the T1 or E1 receive and transmit directions.

• Provides two independent de-jittered T1 or E1 recovered clocks for system timing and redundancy.

• Provides per-DS0 line loopback and per link diagnostic and line loopbacks.

• Provides an on-board programmable binary sequence generator and detector for error testing at DS3 rates. Includes support for patterns recommended in ITU-T O.151.

• Also provides PRBS generators and detectors on each tributary for error testing at DS1, E1 and NxDS0 rates as recommended in ITU-T O.151 and O.152.

• Provides robbed bit signaling extraction and insertion on a per-DS0 basis.

• Provides programmable idle code substitution, data and sign inversion, and digital milliwatt code insertion on a per-DS0 basis.

• Supports the M23 and C-bit parity DS3 formats.

• Standalone unchannelized DS3 framer mode for access to the entire DS3 payload.

• When configured to operate as a DS3 Framer, gapped transmit and receive clocks can be optionally generated for interface to link layer devices which only need access to payload data bits.

• DS3 Transmit clock source can be selected from either an external oscillator or from the receive side clock (loop-timed).

• Register level compatibility with the PM4388 TOCTL Octal T1 Framer, the PM6388 EOCTL Octal E1 Framer, the PM4351 COMET E1/T1 transceiver and the PM8313 D3MX M13 Multiplexer/Demultiplexer.

• Provides a generic 8-bit microprocessor bus interface for configuration, control and status monitoring.

• Provides a standard 5 signal P1149.1 JTAG test port for boundary scan board test purposes.

• Low power 2.5V/3.3V CMOS technology. All pins are 5V tolerant.

• 324-pin fine pitch PBGA package (23mm x 23mm). Supports industrial temperature range (-40°C to 85°C) operation.

APPLICATIONS

• High density T1 interfaces for multiplexers, multi-service switches, routers and digital modems.

• High density E1 interfaces for multiplexers, multi-service switches, routers and digital modems.

• Frame Relay switches and access devices (FRADS)

• M23 Based M13 Multiplexer

• C-Bit Parity Based M13 Multiplexer

• Channelized and Unchannelized DS3 Frame Relay Interfaces