PHOTOLOGIC HERMETIC SENSORS

Features: ● Four output options ● High noise immunity ● Direct TTL/LSTTL interface ● TO-18 hermetic package ● Mechanically and spectrally matched to the OP130 series devices ● Two sensitivity options ● Data rate 200 kBaud

Photologic Hermetic Sensors

Description: All OPL800, OPL801, OPL820 and OPL821 sensors consist of a photodiode, a linear amplifier and a Schmitt trigger on a single silicon chip (monolithic chip for OPL820 and OPL821). OPL810, OPL811, OPL812 and OPL813 sensors also have a voltage regulator added to their photologic chips. E

Photologic, BTP

•Four output options available\n• High noise immunity\n• Direct TTL/LSTTL interface\n• TO-18 hermetically sealed package\n• Sensors mechanically and spectrally matched to other Optek devices;

封装/外壳：TO-18 小型 包装：散装 描述：SENSOR PHOTOLOGIC HERMETIC TO-18 传感器，变送器 光学传感器 - 光检测器 - 逻辑输出

Photologic Hermetic Sensors

Description: All OPL800, OPL801, OPL820 and OPL821 sensors consist of a photodiode, a linear amplifier and a Schmitt trigger on a single silicon chip (monolithic chip for OPL820 and OPL821). OPL810, OPL811, OPL812 and OPL813 sensors also have a voltage regulator added to their photologic chips. E

PHOTOLOGIC HERMETIC SENSORS

Features: ● Four output options ● High noise immunity ● Direct TTL/LSTTL interface ● TO-18 hermetic package ● Mechanically and spectrally matched to the OP130 series devices ● Two sensitivity options ● Data rate 200 kBaud

封装/外壳：TO-18 小型 包装：散装 描述：SENSOR PHOTOLOGIC HERMETIC TO-18 传感器，变送器 光学传感器 - 光检测器 - 逻辑输出

3-Pin Microprocessor Reset Monitors

The MAX809 and MAX810 are cost–effective system supervisor circuits designed to monitor VCC in digital systems and provide a reset signal to the host processor when necessary. No external components are required. Features • Precision VCC Monitor for 2.5 V, 3.0 V, 3.3 V, and 5.0 V Supplies • Pre

3-Pin Microprocessor Reset Monitors

The MAX809 and MAX810 are cost–effective system supervisor circuits designed to monitor VCC in digital systems and provide a reset signal to the host processor when necessary. No external components are required. Features • Precision VCC Monitor for 2.5 V, 3.0 V, 3.3 V, and 5.0 V Supplies • Pre

3-Pin Microprocessor Reset Monitors

The MAX809 and MAX810 are cost–effective system supervisor circuits designed to monitor VCC in digital systems and provide a reset signal to the host processor when necessary. No external components are required. Features • Precision VCC Monitor for 2.5 V, 3.0 V, 3.3 V, and 5.0 V Supplies • Pre

NPN SILICON EPITAXIAL TRANSISTOR WITH BUILT-IN 2 x 2SC5006 FLAT-LEAD 6-PIN THIN-TYPE ULTRA SUPER MINIMOLD

DESCRIPTION The µPA810TC has built-in low-voltage two transistors which are designed to amplify low noise in the VHF band to the UHF band. FEATURES • Low noise: NF = 1.2 dB TYP. @ f = 1 GHz, VCE= 3 V, IC= 7 mA • High gain: |S21e|2= 9.0 dB TYP. @ f = 1 GHz, VCE= 3 V, IC= 7 mA • Fla

NPN SILICON EPITAXIAL TRANSISTOR WITH BUILT-IN 2 x 2SC5006 FLAT-LEAD 6-PIN THIN-TYPE ULTRA SUPER MINIMOLD

DESCRIPTION The µPA810TC has built-in low-voltage two transistors which are designed to amplify low noise in the VHF band to the UHF band. FEATURES • Low noise: NF = 1.2 dB TYP. @ f = 1 GHz, VCE= 3 V, IC= 7 mA • High gain: |S21e|2= 9.0 dB TYP. @ f = 1 GHz, VCE= 3 V, IC= 7 mA • Fla