8-bit micro-controller

General Description This EPROM-Based 8-bit micro-controller uses a fully static CMOS design technology combines higher speeds and smaller size with the low power and high noise immunity of CMOS. On chip memory system includes 1.0 K(for MDT2010) bytes of ROM, and 32 bytes of static RAM.

EPROM-Based 8-bit micro-controller

General Description\nThis EPROM-Based 8-bit micro-controller uses a fully static CMOS design technology combines higher speeds and smaller size with the low power and high noise immunity of CMOS.\nOn chip memory system includes 1.0 K(for MDT2010) bytes of ROM, and 32 bytes of static RAM. The followings are some of the features on the hardware and software :\nFully COMS static design\n8-bit data bus\nOn chip ROM size :1 K words for MDT2010\nInternal RAM size : 32 bytes (25 general purpose registers, 7 special registers)\n36 single word instructions\n14-bit instructions\n2-level stack;

8 位CMOS 单片机

8-bit micro-controller uses a fully static CMOS design technology

文件：76 Kbytes Page：17 Pages

8-bit micro-controller

General Description This EPROM-Based 8-bit micro-controller uses a fully static CMOS design technology combines higher speeds and smaller size with the low power and high noise immunity of CMOS. On chip memory system includes 1.0 K(for MDT2010) bytes of ROM, and 32 bytes of static RAM.

8-bit micro-controller

General Description This EPROM-Based 8-bit micro-controller uses a fully static CMOS design technology combines higher speeds and smaller size with the low power and high noise immunity of CMOS. On chip memory system includes 1.0 K(for MDT2010) bytes of ROM, and 32 bytes of static RAM.

8-bit micro-controller

General Description This EPROM-Based 8-bit micro-controller uses a fully static CMOS design technology combines higher speeds and smaller size with the low power and high noise immunity of CMOS. On chip memory system includes 1.0 K(for MDT2010) bytes of ROM, and 32 bytes of static RAM.

8-bit micro-controller

IN-LINE GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER(VOLTAGE - 50 to 1000 Volts CURRENT - 2.0 Amperes)

FEATURES • Plastic material has Underwriters Laboratory Flammability Classification 94V-O • Ideal for printed circuit board • Reliable low cost construction utilizing molded plastic technique • Surge overload rating : 60 Amperes peak

GLASS PASSIVATED JUNCTION PLASTIC RECTIFIER(VOLTAGE - 50 to 1000 Volts CURRENT - 2.0 Amperes)

VOLTAGE - 50 to 1000 Volts CURRENT - 2.0 Amperes FEATURES Plastic package has Underwriters Laboratory Flammability Classification 94V-O utilizing Flame Retardant Epoxy Molding Compound 2.0 ampere operation at TA=55 ¢J with no thermal runaway Exceeds environmental standards

PLASTIC SILICON RECTIFIER(VOLTAGE 50 to 1000 Volts CURRENT - 2.0 Amperes)

VOLTAGE 50 to 1000 Volts CURRENT - 2.0 Amperes FEATURES • Low cost • High current capability • Plastic package has Underwriters Laboratories Flammability Classification 94V-O utilizing Flame Retardant Epoxy Molding Compound. • 2.0 ampere operation at TA = 55°C with no thermal runawa

POWER RECTIFIERS(20A,50-200V)

Switchmode Full Plastic Dual Ultrafast Power Rectifiers Designed for use in switching power supplies, inverters and as free wheeling diodes. These state-of-the-art devices have the following features: ✱ High Surge Capacity ✱ Low Power Loss, High Efficiency ✱ Glass Passivated chip junction

COMPENSATED PRESSURE SENSOR

文件：91.75 Kbytes Page：4 Pages