Low-Noise, Regulated, Negative Charge-Pump Power Supplies for GaAsFET Bias

General Description The MAX850–MAX853 low-noise, inverting, charge pump power supplies are ideal for biasing GaAsFETs in cellular telephone transmitter amplifiers. The MAX850–MAX852 offer both preset (-4.1V) and adjustable (-0.5V to -9.0V) output voltages. The MAX853 uses an external positive co

低噪声、稳压型、负输出电荷泵，用于GaAsFET偏置电源

MAX850-MAX853低噪声、反相电荷泵电源非常适合用于偏置蜂窝电话发射器放大器中的GaAsFET。\n\n MAX850-MAX852提供预设(-4.1V)和可调（-0.5V至-9.0V）输出电压。MAX853使用外部正控制电压来设置负输出电压。所有四款器件的输入电压范围均为4.5V至10V。输出电流为5mA。\n\n 内部线性稳压器将输出电压纹波降至2mVP-P。对于充分滤波的控制电压(VCTRL)，MAX853可实现低于1mVP-P的典型输出纹波。在整个温度范围内，最大电源电流为3mA，最大关断电流小于1µA（MAX851最大为5µA）。\n\n   • 5mA时提供-4.1V固定输出或-0.5V至-9V可调输出\n\n• 输入电压范围：4.5V至10V\n\n• 2mVP-P输出电压纹波(MAX850-MAX852)\n\n• 1mVP-P输出电压纹波(MAX853)\n\n• 100kHz电荷泵开关频率(MAX850/MAX851/MAX853)\n\n• 外部同步时钟输入(MAX852)\n\n• 逻辑电平关断模式：整个温度范围内最大1µA (MAX850/MAX852/MAX853)\n\n• 低成本、8引脚SO封装;

Dual Low-Dropout Linear Regulators with RESETor Low-Noise Output in UCSP or QFN

General Description The MAX8530/MAX8531 offer the benefits of lowdropout voltage and ultra-low power regulation in subminiaturized UCSP and QFN packages with an integrated microprocessor reset circuit (MAX8530 only). The devices operate from a 2.5V to 6.5V input and deliver up to 200mA and 150mA

Dual Low-Dropout Linear Regulators with RESETor Low-Noise Output in UCSP or QFN

General Description The MAX8530/MAX8531 offer the benefits of lowdropout voltage and ultra-low power regulation in subminiaturized UCSP and QFN packages with an integrated microprocessor reset circuit (MAX8530 only). The devices operate from a 2.5V to 6.5V input and deliver up to 200mA and 150mA

Dual Low-Dropout Linear Regulators with RESETor Low-Noise Output in UCSP or QFN

General Description The MAX8530/MAX8531 offer the benefits of lowdropout voltage and ultra-low power regulation in subminiaturized UCSP and QFN packages with an integrated microprocessor reset circuit (MAX8530 only). The devices operate from a 2.5V to 6.5V input and deliver up to 200mA and 150mA

Dual Low-Dropout Linear Regulators with RESETor Low-Noise Output in UCSP or QFN

General Description The MAX8530/MAX8531 offer the benefits of lowdropout voltage and ultra-low power regulation in subminiaturized UCSP and QFN packages with an integrated microprocessor reset circuit (MAX8530 only). The devices operate from a 2.5V to 6.5V input and deliver up to 200mA and 150mA

双路、低压差线性稳压器，提供复位输出或低噪声输出，UCSP或QFN封装

MAX8530/MAX8531采用微型UCSP和QFN封装，内置集成的微处理器复位电路(仅MAX8530)，可提供低压差电压和超低功率稳压等优点。这两款器件接受2.5V至6.5V的输入电压，输出电流可达200mA和150mA，且在100mA输出电流时具有100mV的典型低压差。MAX8530/MAX8531内置一个P沟道MOSFET调整管，电源电流可保持在130µA (两个LDO都工作时)，与负载电流和压差无关。其他功能包括短路保护和热关断保护。\n\n MAX8530为微处理器提供漏极开路、低电平有效输出，以监测输出OUT1，且无需外部元件和调节。当OUT1降到标称输出电压87&# • OUT1保证200mA输出电流\n• OUT2保证150mA输出电流\n• 两路LDO在100mA负载时都能保证100mV (典型值)的低压差\n• 漏极开路、低电平有效的100ms (最小)复位定时器(MAX8530)\n• 40µVRMS低输出噪声(MAX8531)\n• 130µA低电源工作电流\n• 关断电流小于1µA\n• 热过载和短路保护\n• 输出电流限制\n• 提供小巧的封装\n• 1.16 x 1.57 x 0.6mm UCSP (3 x 2焊球)\n• 3mm x 3mm薄型QFN;

Dual Low-Dropout Linear Regulators with RESETor Low-Noise Output in UCSP or QFN

General Description The MAX8530/MAX8531 offer the benefits of lowdropout voltage and ultra-low power regulation in subminiaturized UCSP and QFN packages with an integrated microprocessor reset circuit (MAX8530 only). The devices operate from a 2.5V to 6.5V input and deliver up to 200mA and 150mA

Dual Low-Dropout Linear Regulators with RESETor Low-Noise Output in UCSP or QFN

General Description The MAX8530/MAX8531 offer the benefits of lowdropout voltage and ultra-low power regulation in subminiaturized UCSP and QFN packages with an integrated microprocessor reset circuit (MAX8530 only). The devices operate from a 2.5V to 6.5V input and deliver up to 200mA and 150mA

Low-Noise, Low-Dropout, 200mA Linear Regulator in UCSP

General Description The MAX8532 offers the benefits of low-dropout voltage and ultra-low power regulation in a subminiaturized UCSP, making it ideal for space-restricted portable equipment. The device operates from a 2.5V to 6.5V input and delivers up to 200mA, with low dropout of 100mV (typ) at

低噪声、低压差、200mA线性稳压器，UCSP封装

MAX8532采用微型UCSP封装，提供低压差和超低功率稳压等优点，尤其适合于空间受限的手持设备。该器件工作于2.5V至6.5V输入电压，输出电流高达200mA，且在100mA输出电流时具有典型值100mV的低压差。MAX8532内置P沟道MOSFET调整管，电源电流保持在80µA，与负载电流和压差无关。其他功能包括短路保护和热关断保护。\n\n MAX8532包含一个为降低输出噪声(40µVRMS)的基准旁路引脚和一个逻辑控制的关断输入引脚。该器件采用微型6引脚UCSP封装。\n\n • 200mA保证输出电流\n• 100mA负载时100mV (典型值)低压差\n• 40µVRMS低输出噪声\n• 80µA低电源工作电流\n• 62dB的PSRR\n• 关断电流小于1µA\n• 热过载和短路保护\n• 输出电流限制\n• 小巧的1.16mm x 1.57mm x 0.66mm UCSP (3 x 2焊球)封装;

Low-Noise, Low-Dropout, 200mA Linear Regulator in UCSP

General Description The MAX8532 offers the benefits of low-dropout voltage and ultra-low power regulation in a subminiaturized UCSP, making it ideal for space-restricted portable equipment. The device operates from a 2.5V to 6.5V input and delivers up to 200mA, with low dropout of 100mV (typ) at

Low-Noise, Low-Dropout, 200mA Linear Regulator in UCSP

General Description The MAX8532 offers the benefits of low-dropout voltage and ultra-low power regulation in a subminiaturized UCSP, making it ideal for space-restricted portable equipment. The device operates from a 2.5V to 6.5V input and delivers up to 200mA, with low dropout of 100mV (typ) at

ORing MOSFET Controllers with Fastest Fault Isolation for Redundant Power Supplies

General Description Critical loads often employ parallel-connected power supplies with redundancy in order to enhance system reliability. The MAX8535/MAX8536/MAX8585 are highly integrated but inexpensive MOSFET controllers that provide isolation and redundant power capability in high-reliability

ORing MOSFET Controllers with Fastest Fault Isolation for Redundant Power Supplies

General Description Critical loads often employ parallel-connected power supplies with redundancy in order to enhance system reliability. The MAX8535/MAX8536/MAX8585 are highly integrated but inexpensive MOSFET controllers that provide isolation and redundant power capability in high-reliability

ORing MOSFET Controllers with Fastest Fault Isolation for Redundant Power Supplies

General Description Critical loads often employ parallel-connected power supplies with redundancy in order to enhance system reliability. The MAX8535/MAX8536/MAX8585 are highly integrated but inexpensive MOSFET controllers that provide isolation and redundant power capability in high-reliability

ORing MOSFET Controllers with Fastest Fault Isolation for Redundant Power Supplies

General Description Critical loads often employ parallel-connected power supplies with redundancy in order to enhance system reliability. The MAX8535/MAX8536/MAX8585 are highly integrated but inexpensive MOSFET controllers that provide isolation and redundant power capability in high-reliability

Dual-Synchronous Buck Controllers for Point-of-Load, Tracking, and DDR Memory Power Supplies

General Description The MAX8537/MAX8539 controllers provide a complete power-management solution for both double-data-rate (DDR) and combiner supplies. The MAX8537 and MAX8539 are configured for out-of-phase and in-phase DDR power-supply operations, respectively, and generate three outputs: the m

PLASTIC ENCAPSULATED DEVICES

[MAXIM INTEGRATED PRODUCTS] Device Description General The MAX8538 is configured as a dual out-of-phase controller for point-of-load supplies. Each buck controller can source or sink up to 25A of current, while the termination reference can supply up to 15mA output. The MAX8538 uses constant-f

Dual-Synchronous Buck Controllers for Point-of-Load, Tracking, and DDR Memory Power Supplies

General Description The MAX8537/MAX8539 controllers provide a complete power-management solution for both double-data-rate (DDR) and combiner supplies. The MAX8537 and MAX8539 are configured for out-of-phase and in-phase DDR power-supply operations, respectively, and generate three outputs: the m

PLASTIC ENCAPSULATED DEVICES

[MAXIM INTEGRATED PRODUCTS] Device Description General The MAX8538 is configured as a dual out-of-phase controller for point-of-load supplies. Each buck controller can source or sink up to 25A of current, while the termination reference can supply up to 15mA output. The MAX8538 uses constant-f

PLASTIC ENCAPSULATED DEVICES

[MAXIM INTEGRATED PRODUCTS] Device Description General The MAX8538 is configured as a dual out-of-phase controller for point-of-load supplies. Each buck controller can source or sink up to 25A of current, while the termination reference can supply up to 15mA output. The MAX8538 uses constant-f

Dual-Synchronous Buck Controllers for Point-of-Load, Tracking, and DDR Memory Power Supplies

General Description The MAX8537/MAX8539 controllers provide a complete power-management solution for both double-data-rate (DDR) and combiner supplies. The MAX8537 and MAX8539 are configured for out-of-phase and in-phase DDR power-supply operations, respectively, and generate three outputs: the m

PLASTIC ENCAPSULATED DEVICES

[MAXIM INTEGRATED PRODUCTS] Device Description General The MAX8538 is configured as a dual out-of-phase controller for point-of-load supplies. Each buck controller can source or sink up to 25A of current, while the termination reference can supply up to 15mA output. The MAX8538 uses constant-f

Dual-Synchronous Buck Controllers for Point-of-Load, Tracking, and DDR Memory Power Supplies

General Description The MAX8537/MAX8539 controllers provide a complete power-management solution for both double-data-rate (DDR) and combiner supplies. The MAX8537 and MAX8539 are configured for out-of-phase and in-phase DDR power-supply operations, respectively, and generate three outputs: the m

Low-Noise, Regulated, Negative Charge-Pump Power Supplies for GaAsFET Bias

General Description The MAX850–MAX853 low-noise, inverting, charge pump power supplies are ideal for biasing GaAsFETs in cellular telephone transmitter amplifiers. The MAX850–MAX852 offer both preset (-4.1V) and adjustable (-0.5V to -9.0V) output voltages. The MAX853 uses an external positive co

Low-Noise, Regulated, Negative Charge-Pump Power Supplies for GaAsFET Bias

General Description The MAX850–MAX853 low-noise, inverting, charge pump power supplies are ideal for biasing GaAsFETs in cellular telephone transmitter amplifiers. The MAX850–MAX852 offer both preset (-4.1V) and adjustable (-0.5V to -9.0V) output voltages. The MAX853 uses an external positive co

Low-Noise, Regulated, Negative Charge-Pump Power Supplies for GaAsFET Bias

General Description The MAX850–MAX853 low-noise, inverting, charge pump power supplies are ideal for biasing GaAsFETs in cellular telephone transmitter amplifiers. The MAX850–MAX852 offer both preset (-4.1V) and adjustable (-0.5V to -9.0V) output voltages. The MAX853 uses an external positive co

Low-Noise, Regulated, Negative Charge-Pump Power Supplies for GaAsFET Bias

General Description The MAX850–MAX853 low-noise, inverting, charge pump power supplies are ideal for biasing GaAsFETs in cellular telephone transmitter amplifiers. The MAX850–MAX852 offer both preset (-4.1V) and adjustable (-0.5V to -9.0V) output voltages. The MAX853 uses an external positive co

Dual Low-Dropout Linear Regulators with RESET or Low-Noise Output in UCSP or QFN

文件：255.48 Kbytes Page：12 Pages

Dual Low-Dropout Linear Regulators with RESET or Low-Noise Output in UCSP or QFN

文件：255.48 Kbytes Page：12 Pages

Dual Low-Dropout Linear Regulators with RESET or Low-Noise Output in UCSP or QFN

文件：255.48 Kbytes Page：12 Pages

功能：- 包装：带 描述：IC REG LINEAR 2.85V/2.85V 6UCSP 集成电路（IC） 稳压器 - DC-DC 开关稳压器

封装/外壳：6-WFBGA，WLBGA 包装：卷带（TR） 描述：IC REG LINEAR 2.85V/2.85V 6UCSP 集成电路（IC） 稳压器 - 线性

Dual Low-Dropout Linear Regulators with RESET or Low-Noise Output in UCSP or QFN

文件：255.48 Kbytes Page：12 Pages

Dual Low-Dropout Linear Regulators with RESET or Low-Noise Output in UCSP or QFN

文件：255.48 Kbytes Page：12 Pages

Dual Low-Dropout Linear Regulators with RESET or Low-Noise Output in UCSP or QFN

文件：255.48 Kbytes Page：12 Pages

Dual Low-Dropout Linear Regulators with RESET or Low-Noise Output in UCSP or QFN

文件：255.48 Kbytes Page：12 Pages

Dual Low-Dropout Linear Regulators with RESET or Low-Noise Output in UCSP or QFN

文件：255.48 Kbytes Page：12 Pages

Dual Low-Dropout Linear Regulators with RESET or Low-Noise Output in UCSP or QFN

文件：255.48 Kbytes Page：12 Pages

Dual Low-Dropout Linear Regulators with RESET or Low-Noise Output in UCSP or QFN

文件：255.48 Kbytes Page：12 Pages

Dual Low-Dropout Linear Regulators with RESET or Low-Noise Output in UCSP or QFN

文件：255.48 Kbytes Page：12 Pages

Dual Low-Dropout Linear Regulators with RESET or Low-Noise Output in UCSP or QFN

文件：255.48 Kbytes Page：12 Pages

Low-Noise, Low-Dropout,200mA Linear Regulator in UCSP

文件：315.85 Kbytes Page：8 Pages

Low-Noise, Low-Dropout,200mA Linear Regulator in UCSP

文件：315.85 Kbytes Page：8 Pages

Low-Noise, Low-Dropout,200mA Linear Regulator in UCSP

文件：315.85 Kbytes Page：8 Pages

Low-Noise, Low-Dropout,200mA Linear Regulator in UCSP

文件：315.85 Kbytes Page：8 Pages

Low-Noise, Low-Dropout,200mA Linear Regulator in UCSP

文件：315.85 Kbytes Page：8 Pages

Low-Noise, Low-Dropout,200mA Linear Regulator in UCSP

文件：315.85 Kbytes Page：8 Pages

Smallest, Most Reliable, 12V, Infiniband- Compliant Hot-Swap Controller

文件：240.08 Kbytes Page：10 Pages

Smallest, Most Reliable, 12V, Infiniband- Compliant Hot-Swap Controller

文件：240.08 Kbytes Page：10 Pages

Eliminates ORing Diode Power Dissipation

文件：113.56 Kbytes Page：7 Pages

Eliminates ORing Diode Power Dissipation

文件：113.56 Kbytes Page：7 Pages

Lossless Adjustable Hiccup Current Limit

文件：228.08 Kbytes Page：11 Pages

Lossless Adjustable Hiccup Current Limit

文件：228.08 Kbytes Page：11 Pages

Integrated Circuit Low Power, Narrow Band, FM IF System

Description: The NTE853 is a low power narrow band FM IF system which includes: Oscillator, Mixer, Limiting Amplifier, Quadrature Discriminator, Active Filter, Squelch, Scan Control and Mute Switch. The NTE853 is designed for use in FM dual conversion communications equipment. Features: ● Low D

FAST RECOVERY RECTIFIER DIODE

DESCRIPTION Their high efficiency and high reliability combined with small size and low cost make these fast recovery rectifier diode very attractive components for many demanding applications. ■ LOW FORWARD VOLTAGE DROP ■ HIGH SURGE CURRENT CAPABILITY APPLICATIONS ■ AC-DC POWER SUPPLIES AND

FAST RECOVERY RECTIFIER DIODES

DESCRIPTION Their high efficiency and high reliability combined with small size and low cost make these fast recovery rectifier diodes very attractive components for many demanding applications. ■ LOW FORWARD VOLTAGE DROP ■ HIGH SURGE CURRENT CAPABILITY APPLICATIONS ■ AC-DC POWER SUPPLIES AND

REGULATED GaAs FET BIAS SUPPLY

文件：75.43 Kbytes Page：7 Pages

REGULATED GaAs FET BIAS SUPPLY

文件：75.43 Kbytes Page：7 Pages