180MHz, 1mA Power Efficient Rail-to-Rail I/O Op Amps

FEATURES APPLICATIONS n Gain Bandwidth Product: 180MHz n –3dB Frequency (AV = 1): 120MHz n Low Quiescent Current: 1mA Max n High Slew Rate: 90V/μs n Input Common Mode Range Includes Both Rails n Output Swings Rail-to-Rail n Low Broadband Voltage Noise: 4.2nV/√Hz n Power-Down Mode: 42μA n

60MHz、轨至轨输出、1.9nV/√Hz、1.2mA 运放系列

LT®6233 / LT6234 / LT6235 是单/双/四路低噪声、轨至轨输出、单位增益稳定的运算放大器，它们具有 1.9nV/√Hz 的噪声电压，每个放大器仅吸收 1.2mA 的电源电流。这些放大器把非常低噪声和电源电流与 60MHz 的增益带宽乘积、17V/us 的转换速率结合在一起，并针对低电源电压信号调节系统进行了优化。LT6233-10 是专门针对增益较高的应用而优化的单路放大器，可实现较高的增益带宽和转换速率。LT6233 和 LT6233-10 包括一个使能引脚，该引脚可被用来将电源电流减小至 10µA 以下。\n\n 该放大器系列具有一个摆动在任一电源轨的 50 • 低噪声电压：1.9nV/√Hz \n• 低电源电流：1.2mA/放大器 (最大值) \n• 低失调电压：350µV (最大值) \n• 增益带宽乘积：  \n• LT6233：60MHz；AV ≥ 1  \n• LT6233-10：375MHz；AV ≥ 10 \n• 宽电源电压范围：3V 至 12.6V \n• 轨至轨输出摆幅 \n• 共模抑制比：115dB (典型值) \n• 输出电流：30mA \n• 工作温度范围：-40°C 至 85°C \n• LT6233 在停机模式中的电流为 10µA (最大值) \n• LT6233 / LT6233-10 采用扁平 (高度 1mm) Th;

1.3GHz Low Noise, Low Distortion Differential ADC Driver for 140MHz IF

文件：223.95 Kbytes Page：16 Pages

60MHz, Rail-to-Rail Output, 1.9nV / SIGME Hz, 1.15mA Op Amp Family

文件：727.8 Kbytes Page：24 Pages

2.4GHz Low Noise, Low Distortion Differential ADC Driver for 300MHz IF

文件：213.49 Kbytes Page：16 Pages

Octal, 18-Bit, 200ksps Differential SoftSpan ADC with Wide Input Common Mode Range

文件：1.88721 Mbytes Page：40 Pages

Octal, 16-Bit, 200ksps Differential SoftSpan ADC with Wide Input Common Mode Range

文件：2.01901 Mbytes Page：40 Pages

60MHz, Rail-to-Rail Output

文件：778.46 Kbytes Page：24 Pages

60MHz, Rail-to-Rail Output, 1.9nV / SIGME Hz, 1.15mA Op Amp Family

文件：727.8 Kbytes Page：24 Pages

60MHz, Rail-to-Rail Output, 1.9nV / SIGME Hz, 1.15mA Op Amp Family

文件：727.8 Kbytes Page：24 Pages

60MHz, Rail-to-Rail Output, 1.9nV / SIGME Hz, 1.15mA Op Amp Family

文件：727.8 Kbytes Page：24 Pages

60MHz, Rail-to-Rail Output, 1.9nV / SIGME Hz, 1.15mA Op Amp Family

文件：727.8 Kbytes Page：24 Pages

THREE PHASE MOTOR DRIVER

Description The L6234 is a triple half bridge to drive a brushless DC motor Features ● Supply voltage from 7 to 52 V ● 5 A peak current ● RDSon 0.3 Ω typ. value at 25 °C ● Cross conduction protection ● TTL compatible driver ● Operating frequency up to 150 kHz ● Thermal shutdown ● In

THREE PHASE MOTOR DRIVER

Description The L6234 is a triple half bridge to drive a brushless DC motor Features ● Supply voltage from 7 to 52 V ● 5 A peak current ● RDSon 0.3 Ω typ. value at 25 °C ● Cross conduction protection ● TTL compatible driver ● Operating frequency up to 150 kHz ● Thermal shutdown ● In

Powerblock Module

Description: The NTE6234 uses 2 high voltage power diodes in series and the semiconductors are electrically isolated from the metal base, allowing common heatsinks and compact assemblies to be built. This device is intended for general purpose applications such as battery chargers, welders and

E-Rate Multiplexer

E-Rate Multiplexer

E-Rate Multiplexer

文件：327.1 Kbytes Page：24 Pages