Actuator Driver for Portable CD Players

Overview The LB8106 is a four-channel actuator driver for driving the focus coil, tracking coil, spindle motor and seld motor in portable CD players.

EasyCom Com Unit for PROFIBUS DP/DP-V1

Actuator Driver for Portable CD Players

Overview The LB8106 is a four-channel actuator driver for driving the focus coil, tracking coil, spindle motor and seld motor in portable CD players.

Com Unit for MODBUS RTU

Portable CD Player Actuator Driver

Overview The LB8107M is a portable CD player mechanism actuator driver. It operates on a 2.4 V power supply, which corresponds to two rechargeable Ni-Cd cells. Functions and Features • Four H bridge driver channels on chip, one each for the four CD actuators; focus coil, tracking coil, spindle

Actuator Driver for Portable CD Players?

Applications The LB8108M is an actuator driver for use in portable CD players that operate at a power supply voltage of 2.4 (two nicad batteries) or 3.0 V (two dry-cell batteries).

Actuator Driver for Portable CD Players?

Applications The LB8108M is an actuator driver for use in portable CD players that operate at a power supply voltage of 2.4 (two nicad batteries) or 3.0 V (two dry-cell batteries).

Unicom Com Unit for PROFIBUS DP/DP-V1

Actuator Driver for Portable CD Players

Overview The LB8109M is an actuator driver IC designed for portable CD players that operate at 2.4 V (two Ni-Cd batteries) or 3.0 V (two dry cells). Functions and Features • H bridge drivers (output dynamic range maximum is about 2 V) on chip for four channels to drive each CD actuator (the foc

Position and option witch commend

文件：143.25 Kbytes Page：4 Pages

Actuator Driver for Portable CD Players

Portable CD Player Actuator Driver

Actuator Driver for Portable CD Players

3-Pin Microprocessor Reset Monitors

The MAX809 and MAX810 are cost–effective system supervisor circuits designed to monitor VCC in digital systems and provide a reset signal to the host processor when necessary. No external components are required. Features • Precision VCC Monitor for 2.5 V, 3.0 V, 3.3 V, and 5.0 V Supplies • Pre

3-Pin Microprocessor Reset Monitors

The MAX809 and MAX810 are cost–effective system supervisor circuits designed to monitor VCC in digital systems and provide a reset signal to the host processor when necessary. No external components are required. Features • Precision VCC Monitor for 2.5 V, 3.0 V, 3.3 V, and 5.0 V Supplies • Pre

3-Pin Microprocessor Reset Monitors

The MAX809 and MAX810 are cost–effective system supervisor circuits designed to monitor VCC in digital systems and provide a reset signal to the host processor when necessary. No external components are required. Features • Precision VCC Monitor for 2.5 V, 3.0 V, 3.3 V, and 5.0 V Supplies • Pre

NPN SILICON EPITAXIAL TRANSISTOR WITH BUILT-IN 2 x 2SC5006 FLAT-LEAD 6-PIN THIN-TYPE ULTRA SUPER MINIMOLD

DESCRIPTION The µPA810TC has built-in low-voltage two transistors which are designed to amplify low noise in the VHF band to the UHF band. FEATURES • Low noise: NF = 1.2 dB TYP. @ f = 1 GHz, VCE= 3 V, IC= 7 mA • High gain: |S21e|2= 9.0 dB TYP. @ f = 1 GHz, VCE= 3 V, IC= 7 mA • Fla

NPN SILICON EPITAXIAL TRANSISTOR WITH BUILT-IN 2 x 2SC5006 FLAT-LEAD 6-PIN THIN-TYPE ULTRA SUPER MINIMOLD

DESCRIPTION The µPA810TC has built-in low-voltage two transistors which are designed to amplify low noise in the VHF band to the UHF band. FEATURES • Low noise: NF = 1.2 dB TYP. @ f = 1 GHz, VCE= 3 V, IC= 7 mA • High gain: |S21e|2= 9.0 dB TYP. @ f = 1 GHz, VCE= 3 V, IC= 7 mA • Fla