Programmable Linear Hall-Effect Sensor

Introduction The Hall programmer board V 5.1 is a general-purpose programming interface which is capable of addressing the programmable Micronas Hall-effect sensor families HAL 8xy and HAL 100x. The Hall programmer board V 5.1 is fully software compatible to the Hall programmer board V 4.1. Henc

Programmer Board

文件：752.73 Kbytes Page：102 Pages

可编程线性霍尔效应传感器

HAL 810和HAL 817是可编程线性霍尔传感器，可用于角度或者距离测量。主要参数是在非易失内存中进行编程的。HAL 817有比例输出特性。输出电压与磁通量和供电电压成比例。HAL 810提供脉宽调制输出。产品有带斩波偏置补偿的温度补偿霍尔片，交流直流转换器，为标定数据而设的冗余和锁定功能，以及各引脚的保护装置。数据信号处理，模拟偏置，温度飘移和机械应力都不会降低传感器的精确性。传感器、磁场和机械位置形成的偏差可以由客户／用户在最后装配时通过编程来补偿。这是对近来需要机械调整或者激光修正来标定的各种应用的低成本替代方案。HAL 810和HAL 817设计适用于恶劣环境下的汽车和工业应用，供 ·Sensitivity drift over temperature less than ±400 ppm/K\n·Offset drift over temperature less than ±10 μT/K\n·Integral non-linearity error of output signal ±0.5% of VDD\n·Ratiometric error of output signal ±0.5%\n·Low output noise of 6 mV RMS\n·Wire break detection\n·Programmable magnetic ra;

封装/外壳：TO-226-3，TO-92-3（TO-226AA）成形引线 包装：卷带（TR）剪切带（CT）Digi-Reel® 得捷定制卷带 描述：SENSOR HALL EFFECT PWM TO92-UT 传感器，变送器 磁性传感器 - 线性，罗盘（IC）

线性霍尔传感器

线性霍尔传感器

封装/外壳：TO-226-3，TO-92-3（TO-226AA）成形引线 包装：卷带（TR）剪切带（CT）Digi-Reel® 得捷定制卷带 描述：SENSOR HALL EFFECT PWM TO92-UT 传感器，变送器 磁性传感器 - 线性，罗盘（IC）

3-Pin Microprocessor Reset Monitors

The MAX809 and MAX810 are cost–effective system supervisor circuits designed to monitor VCC in digital systems and provide a reset signal to the host processor when necessary. No external components are required. Features • Precision VCC Monitor for 2.5 V, 3.0 V, 3.3 V, and 5.0 V Supplies • Pre

3-Pin Microprocessor Reset Monitors

The MAX809 and MAX810 are cost–effective system supervisor circuits designed to monitor VCC in digital systems and provide a reset signal to the host processor when necessary. No external components are required. Features • Precision VCC Monitor for 2.5 V, 3.0 V, 3.3 V, and 5.0 V Supplies • Pre

3-Pin Microprocessor Reset Monitors

The MAX809 and MAX810 are cost–effective system supervisor circuits designed to monitor VCC in digital systems and provide a reset signal to the host processor when necessary. No external components are required. Features • Precision VCC Monitor for 2.5 V, 3.0 V, 3.3 V, and 5.0 V Supplies • Pre

NPN SILICON EPITAXIAL TRANSISTOR WITH BUILT-IN 2 x 2SC5006 FLAT-LEAD 6-PIN THIN-TYPE ULTRA SUPER MINIMOLD

DESCRIPTION The µPA810TC has built-in low-voltage two transistors which are designed to amplify low noise in the VHF band to the UHF band. FEATURES • Low noise: NF = 1.2 dB TYP. @ f = 1 GHz, VCE= 3 V, IC= 7 mA • High gain: |S21e|2= 9.0 dB TYP. @ f = 1 GHz, VCE= 3 V, IC= 7 mA • Fla

NPN SILICON EPITAXIAL TRANSISTOR WITH BUILT-IN 2 x 2SC5006 FLAT-LEAD 6-PIN THIN-TYPE ULTRA SUPER MINIMOLD

DESCRIPTION The µPA810TC has built-in low-voltage two transistors which are designed to amplify low noise in the VHF band to the UHF band. FEATURES • Low noise: NF = 1.2 dB TYP. @ f = 1 GHz, VCE= 3 V, IC= 7 mA • High gain: |S21e|2= 9.0 dB TYP. @ f = 1 GHz, VCE= 3 V, IC= 7 mA • Fla