Low Voltage Dual Supply 8-Bit Signal Translator with Configurable Voltage Supplies and Signal Levels and 3-STATE Outputs

Description The FXL4245 is a configurable dual-voltage-supply translator designed for bi-directional voltage translation of signals between two voltage levels. The device allows translation between voltages as high as 3.6V to as low as 1.1V. The A port tracks the VCCA level and the B port tracks

低电压双电源 8 位信号转换器，带可配置电压电源和信号电平以及 3 态输出

FXL4245是一款可配置双电压电源转换器，设计用于两个电压电平之间的双向电压信号转换。 FOD073L该器件允许的电压转换范围为最高3.6V，最低1.1V。 A端口跟踪VCCA电平，而B端口跟踪VCCB电平。 两个端口均设计用于接受1.1V至3.6V的电源电压电平。 这就允许在各种电压电平上进行双向电压转换： 1.2V、1.5V、1.8V、2.5V和3.3V。该器件将保持在3态状态，直到两个VCC都达到有效电平，从而允许任一VCC首先上电。 该器件还具有掉电控制电路，如果取消任一VCC，则该电路会将器件置于3态状态。传输/接收(T/R)输入决定通过器件的数据流的方向。 当为高电平时，OE输入 •从1.1V到3.6V两个电平之间的双向接口\n•完全可配置的输入跟踪VCC电平\n•非优先上电；任一VCC都可能首先上电\n•输出保持在3态状态，直到达到有效VCC电平\n•输出保持在3态状态，直到达到有效VCC电平\n•如果任一VCC处于GND状态，则输出将会切换至3态\n•断电保护\n•控制输入(T/R，OE)电平参考VCCA电压\n•24引脚MLP封装\n•ESD保护超过\n•- 4kV人体模型（根据JESD22-A114和Mil Std 883e 3015.7标准）\n•- 8kV人体模型I/O至GND（根据JESD22-A114和Mil Std 883e 3015.7标准）\n•-;

Low-Voltage, Dual-Supply, 8-Bit, Signal Translator

文件：601.03 Kbytes Page：13 Pages

Low Voltage Dual Supply 8-Bit Signal Translator with Configurable Voltage Supplies and Signal Levels and 3-STATE Outputs

Description The FXL4245 is a configurable dual-voltage-supply translator designed for bi-directional voltage translation of signals between two voltage levels. The device allows translation between voltages as high as 3.6V to as low as 1.1V. The A port tracks the VCCA level and the B port tracks

Low-Voltage, Dual-Supply, 8-Bit, Signal Translator with Configurable Voltage Supplies, Signal Levels, and 3-State Outputs

文件：568.48 Kbytes Page：11 Pages

Low-Voltage, Dual-Supply, 8-Bit, Signal Translator

文件：601.03 Kbytes Page：13 Pages

封装/外壳：24-WFQFN 裸露焊盘 包装：卷带（TR）剪切带（CT）Digi-Reel® 得捷定制卷带 描述：IC TRNSLTR BIDIRECTIONAL 24MLP 集成电路（IC） 转换器，电平移位器

Low-Voltage, Dual-Supply, 8-Bit, Signal Translator with Configurable Voltage Supplies, Signal Levels, and 3-State Outputs

文件：568.48 Kbytes Page：11 Pages

Infrared detector module with preamp

Infrared detector module with preamp Non-cooled Type Easy-to-use detector module with built-in preamp These Infrared detector modules with preamp are designed to operate at room temperatures by just connecting to a DC power supply. The detector element is selectable from among InGaAs, PbSe and

Ultra-Small, Rail-to-Rail I/O with Disable, Single-/Dual-Supply, Low-Power Op Amps

文件：495.31 Kbytes Page：11 Pages

Ultra-Small, Rail-to-Rail I/O with Disable, Single-/Dual-Supply, Low-Power Op Amps

文件：495.31 Kbytes Page：11 Pages

10-W Low-Profile 24V-Input Isolated DC/DC Converter

文件：174.58 Kbytes Page：7 Pages