USB UART IC

• Single chip USB to asynchronous serial data transfer interface. • Entire USB protocol handled on the chip. No USB specific firmware programming required. • Fully integrated 1024-bit EEPROM storing device descriptors and CBUS I/O configuration. • Fully integrated USB termination resistors. •

USB UART IC

• Single chip USB to asynchronous serial data transfer interface. • Entire USB protocol handled on the chip. No USB specific firmware programming required. • Fully integrated 1024-bit EEPROM storing device descriptors and CBUS I/O configuration. • Fully integrated USB termination resistors. •

USB Full Speed to Serial UART IC, Includes Oscillator and EEPROM, SSOP-28

The FT232RNL device is added to FTDI’s range of USB UART interface Integrated Circuit Devices. The FT232RNL is a USB to serial UART interface with optional clock generator output, and the new FTDIChip-ID™ security dongle feature. In addition, asynchronous and synchronous bit bang interface modes are ·Single chip USB to asynchronous serial data transfer interface.\n·Entire USB protocol handled on the chip – No USB-specific firmware programming required.\n·UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no parity.\n·Fully assisted hardware or X-On / X;

USB UART IC

• Single chip USB to asynchronous serial data transfer interface. • Entire USB protocol handled on the chip. No USB specific firmware programming required. • Fully integrated 1024-bit EEPROM storing device descriptors and CBUS I/O configuration. • Fully integrated USB termination resistors. •

USB UART IC

• Single chip USB to asynchronous serial data transfer interface. • Entire USB protocol handled on the chip. No USB specific firmware programming required. • Fully integrated 1024-bit EEPROM storing device descriptors and CBUS I/O configuration. • Fully integrated USB termination resistors. •

USB Full Speed to Serial UART IC, Includes Oscillator and EEPROM, QFN-32

The FT232RNQ is added to FTDI’s range of USB UART interface Integrated Circuit Devices. The FT232RNQ is a USB to serial UART interface with optional clock generator output, and the new FTDIChip-ID™ security dongle feature. In addition, asynchronous and synchronous bit bang interface modes are availa ·Single chip USB to asynchronous serial data transfer interface.\n·Entire USB protocol handled on the chip – No USB-specific firmware programming required.\n·UART interface support for 7 or 8 data bits, 1 or 2 stop bits and odd / even / mark / space / no parity.\n·Fully assisted hardware or X-On / X;

USB UART IC

• Single chip USB to asynchronous serial data transfer interface. • Entire USB protocol handled on the chip. No USB specific firmware programming required. • Fully integrated 1024-bit EEPROM storing device descriptors and CBUS I/O configuration. • Fully integrated USB termination resistors. •

VERY HIGHSPEED, ULTRA LOWPOWERCONSUMPTION 5V POWERED RS-232 DRIVERS AND RECEIVERS

Description The ST232A is a 2 driver, 2 receiver device following EIA/TIA-232 and V.28 communication standard. It is particularly suitable for applications where ±12V is not available. The ST232A uses a single 5V power supply and only four external capacitors (0.1µF). Typical applications are i

5V POWERED MULTI-CHANNEL RS-232 DRIVERS AND RECEIVERS

DESCRIPTION The ST232 is a 2 driver, 2 receiver device following EIA/TIA-232 and V.28 communication standard. It is particularly suitable for applications where ±12V is not available. The ST232 uses a single 5V power supply and only four external capacitors (0.1µF). Typical applications are in:

5V POWERED MULTI-CHANNEL RS-232 DRIVERS AND RECEIVERS

DESCRIPTION The ST232 is a 2 driver, 2 receiver device following EIA/TIA-232 and V.28 communication standard. It is particularly suitable for applications where ±12V is not available. The ST232 uses a single 5V power supply and only four external capacitors (0.1µF). Typical applications are in:

5V POWERED MULTI-CHANNEL RS-232 DRIVERS AND RECEIVERS

DESCRIPTION The ST232 is a 2 driver, 2 receiver device following EIA/TIA-232 and V.28 communication standard. It is particularly suitable for applications where ±12V is not available. The ST232 uses a single 5V power supply and only four external capacitors (0.1µF). Typical applications are in:

5V POWERED MULTI-CHANNEL RS-232 DRIVERS AND RECEIVERS

DESCRIPTION The ST232 is a 2 driver, 2 receiver device following EIA/TIA-232 and V.28 communication standard. It is particularly suitable for applications where ±12V is not available. The ST232 uses a single 5V power supply and only four external capacitors (0.1µF). Typical applications are in: