Engineering Catalog 169

Surface Mount LEDs, SOT-23 Package Surface Mount, Bi-Color LEDs, SOT-23 Package Surface Mount, Gull Wing LEDs Surface Mount LEDs (Rectangular Lens) Surface Mount LEDs (Round Lens) Surface Mount LEDs with Resistor - 5V Surface Mount LEDs with Resistor - 12V Surface Mount, Bi-Color LEDs Surf

Industry Standard Dimensions

文件：171.47 Kbytes Page：1 Pages

Low side driver (8 channel, serial interface)

General Description The IC is developed for automotive applications and can also be used in several other application areas. The IC is well suited to drive relays, lamps, bus systems etc. with medium power consumption. The device provides a serial data bus for comunication with a µC and 8 identi

Analog multiplexer 8:1

DESCRIPTION The IC is an 8 channel analog multiplexer with a buffer amplifier. The input signals IN0 to IN7 are fed to the multiplexer consisting of analog transmission gates which are controlled by the digital inputs SEL0-2. The multiplexer is designed for low crosstalk in case of current inje

K-Bus transceiver

DESCRIPTION The IC is designed for communication via bidirectional serial data channels. In addition to the level conversion of transmit and receive signals from the micro processor’s voltage level to the 12V bus level, the device includes plausibility checks in order to guarantee undisturbed b

LIN- / K-Bus transceiver

DESCRIPTION The IC is designed to control bidirectional serial data transmission on bus lines. It supports both LIN- and K-Bus which are selected by the MODE pin. This feature allows an easy migration from K- to LIN-bus without changing the transceiver. The high voltage range and the low standb

Fan control

DESCRIPTION The IC controls the voltage across a DC fan motor as a function of the voltage applied to the control input “SOLL”. The IC delivers the gate voltage for one or two (parallel) external power-FETs, which linearly drive the load current of the motor. The drain currents of the two externa

LIN transceiver with voltage regulator

DESCRIPTION The IC is designed for LIN slave applications. The microcontroller is completely protected from the harsh automotive environment. FEATURES ► Supply voltage range VS 5.25V to 18V ► LIN-Bus transceiver, up to 20kBaud ► Output driver with slewrate control ► Very low standby current

Wide range SMPS with watchdog

DESCRIPTION The IC is developed and optimized for automotive applications where it can generate different output voltages as a flyback converter. The input voltage may be higher or lower than the output voltage. The multi-loop-regulation concept ensures fast response to variation of input voltage

Adjustable, wide input range PFM controller family

DESCRIPTION The family of highly flexible, easy to use PFM controllers is ideal for the use in wide input range switching regulator applications. An advanced PFM control scheme gives these devices the benefits of PWM converters with high efficiency for heavy loads, while us ing very low operati

Adjustable, wide input range PFM controller family

DESCRIPTION The family of highly flexible, easy to use PFM controllers is ideal for the use in wide input range switching regulator applications. An advanced PFM control scheme gives these devices the benefits of PWM converters with high efficiency for heavy loads, while us ing very low operati

Adjustable, wide input range PFM controller family

DESCRIPTION The family of highly flexible, easy to use PFM controllers is ideal for the use in wide input range switching regulator applications. An advanced PFM control scheme gives these devices the benefits of PWM converters with high efficiency for heavy loads, while us ing very low operati

External Adjustable High Efficiency PFM Step-Down Converter

Brief Functional Description The easy to use hysteretic step-down converter provides high efficiency over a wide load and input range with few external components. An advanced PFM control scheme gives this device the benefits of a PWM converter with high efficiency at heavy loads, while using ve

Low side driver (8 channel, parallel interface)

DESCRIPTION The IC is an 8 channel parallel power driver circuit (low side) with microcontroller compatible bidirectional dataports and output status monitoring. FEATURES ► Supply voltage range VDD 4.75V to 5.25V ► Driver supply voltage range VS 5.25V to 25V ► Low standby current (typical

Contact monitor (8 channel to GND, parallel interface)

DESCRIPTION The IC monitors the status of all switch contacts connected to ground continuously . The input currents are compared with the current of an internal reference resistor. The IC is designed to operate with an external series resistor RIN0 to RIN7 of 1kÝ. The current, driven through the

Contact monitor (8 channel to VBAT, parallel interface)

DESCRIPTION The IC monitors the status of all switch contact connected to VS continuously . The input currents are compared with the current of an internal reference resistor. The IC is designed to operate with an external series resistor RIN0 to RIN7 of 1kÝ. The current, driven through the cont

Contact monitor (4 * GND & 4 * VBAT, adjustable, parallel interface)

DESCRIPTION The IC is developed for automotive applications. It continuously monitors the status of two groups of switch contacts connected to GND or VBAT. The input currents are compared to internal references. The IC is designed to operate with an external resistor of 1kÝ. FEATURES ► Program

Contact monitor (4 * GND & 4 * VBAT, parallel interface)

DESCRIPTION The IC is developed for automotive applications. It continuously monitors the status of two groups of switch contacts connected to GND or VBAT. The input currents are compared to internal references. The IC is designed to operate with an external resistor of 1k Ý. FEATURES ► Supply

LCD controller, driver for grey scale, ECB color displays

DESCRIPTION The IC is a low-power CMOS LCD controller/driver, designed to drive grey - scale or ECB color dot matrix graphic displays at multiplex rates of 1:33 or 1:67. FEATURES ► Supply voltage range VDD 2.5V to 3.5V ► On-chip generation of VLCD adjustable from 4.5V to 14.5V ► Single chip L

Sensorless position control of DC-motors

DESCRIPTION The IC enables a µC to track the position of a DC-motor by counting its current ripples. The ripple signal is available on an output pin to connect controllers or dedicated logic. With the bidirectional interface the actual position can be read out and IC parameters can be changed. Ma

Hall sensor- and contact monitor (8 channel, parallel interface)

DESCRIPTION The IC is developed for automotive applications. It continuously monitors up to 8 hall sensors or switches to GND. The input currents are compared to internal references. Currents exceeding – 11mA will force a logic ‘0’ at the output, while currents higher than -6mA will result in a

LIN transceiver

DESCRIPTION The IC interfaces between a µC and a Local Interconnect Network (LIN) bus-line, mainly in automotive sub bus applications. When pin EN is at High level (VDD), a digital input signal at pin TxD is transferred to the fully protected low side driver on pin BUS. The voltage level on pin B

Hall sensor IC

DESCRIPTION The IC contains a Hall sensor and the appropriate measurement system. It detects three levels of upright magnetic field: positive, near zero and negative. These information are provided at two binary coded outputs for any logic or uC. The sampling rate is about 10kHz (typ.) allowing f

LIN transceiver with voltage regulator

DESCRIPTION The IC is designed for LIN slave applications. The microcontroller is completely protected from the harsh automotive environment. FEATURES ► Supply voltage range VS 5.25V to 18V ► LIN-Bus transceiver, up to 20kBaud ► Output driver with slewrate control ► Very low standby current

EC motor control

DESCRIPTION The IC is a PWM EC brushless motor driver/controller to implement a motor regulator together with n-channel power FET B6- configuration and a µC The programmability of parameters (e.g. threshold values of over current, over temperature, motor failures, EMC conditions, etc.) can be use

Non volatile contact monitor

DESCRIPTION The IC is designed for use in electric power window systems to store and display the status of a childproof lock function of the rear windows. The actual status is stored in three bits of the EEPROM whenever switch activity is detected. The redundant information is checked periodicall

LIN transceiver with voltage regulator and watchdog

DESCRIPTION The IC is used as a voltage regulator with an integrated LIN-interface in automotive applications. The voltage regulator supplies an µC in the application. FEATURES ► Operating voltage range (VS) 3V to 27V ► Two selectable output voltages: 5V and 3.3V ±2.0 ► Output current 150mA

Contact monitor to GND or VBAT (16 channel, serial interface)

DESCRIPTION The IC is intended to reduce the costs of products with a large number of inputs and also to reduce software overhead by generating an interrupt on pin change. To decrease the system power dissipation the external driver transistors are only active for 20µs of a 7ms frame correspondin

FlexRay??Transceiver

Brief Functional Description The low cost basic FlexRay™ transceiver is part of the electrical, physical layer in a FlexRay™ communication network. The E910.54 provides an interface between the twisted pair physical bus medium and a communication controller (CC). An SPI interface connects the bus

FlexRay??Transceiver With Wakeup

Brief Functional Description The low cost bus driver is a part of the electrical, physical layer in a FlexRay™ communication network. The E910.55 provides an interface between the twisted pair physical bus medium and a communication controller (CC). An SPI interface connects the bus driver (BD) t

FlexRay??Star Coupler

Brief Functional Description The star coupler is part of the electrical, physical layer in a FlexRay™ communication network. The E910.56 provides interfaces to connect up to four branches of twisted pair physical bus lines to other bus drivers or star couplers. It also interfaces with a communica

Sensorless position control of DC-motors, with drivers

DESCRIPTION The IC features 6 configurable half bridges to drives up to 3 DC motors simultaneously or up to 5 motors sequentially. 3 independent pulse detection circuits convert the commutation current of the motors into countable digital signals for positioning especially of HVAC flap actuators.

Bus controlled steppermotor driver

DESCRIPTION The IC is developed for automotive applications. The stepper motor driver is optimized to drive SAIA stepper motors, but is also verified with several bipolar stepper motors in the market. A stalled detection is fully integrated and does not need a shunt resistor. With a configuration

Sensorless speed control of DC-motors

DESCRIPTION The IC is designed to control the speed of DC-motors. In order to determine the motor speed the commutation-related ripple of the motor current is evaluated and converted to a 5V digital signal for the µC. The filtered motor current is also buffered and provided to the µC’s ADC. Many

Low side dri ver (8 channel , serial inter face )

文件：668.89 Kbytes Page：17 Pages

DUAL CHANNEL PIR SIGNAL PROCESSOR

文件：650.15 Kbytes Page：7 Pages

INTERGRATED CIRCUIT FOR PIR SMART SENSOR

文件：811.85 Kbytes Page：9 Pages

OUTLINE MAGNETIC WORKLAMP

文件：77.73 Kbytes Page：1 Pages

Surface Mount Glass Passivated Single Phase Bridge Rectifier

文件：380.21 Kbytes Page：4 Pages

Surface Mount Glass Passivated Single Phase Bridge Rectifier

文件：371.18 Kbytes Page：4 Pages

Surface Mount Glass Passivated Single Phase Bridge Rectifier

文件：357.11 Kbytes Page：4 Pages

Surface Mount Glass Passivated Single Phase Bridge Rectifier

文件：357.11 Kbytes Page：4 Pages

Surface Mount Glass Passivated Single Phase Bridge Rectifier

文件：357.11 Kbytes Page：4 Pages

Surface Mount Glass Passivated Single Phase Bridge Rectifier

文件：357.11 Kbytes Page：4 Pages

Surface Mount Glass Passivated Single Phase Bridge Rectifier

文件：375.43 Kbytes Page：4 Pages

Surface Mount Glass Passivated Single Phase Bridge Rectifier

文件：373.54 Kbytes Page：4 Pages

Surface Mount Glass Passivated Single Phase Bridge Rectifier

文件：375.43 Kbytes Page：4 Pages

Surface Mount Glass Passivated Single Phase Bridge Rectifier

文件：373.54 Kbytes Page：4 Pages

Surface Mount Glass Passivated Single Phase Bridge Rectifier

文件：372.21 Kbytes Page：4 Pages

Surface Mount Glass Passivated Single Phase Bridge Rectifier

文件：371.74 Kbytes Page：4 Pages

Surface Mount Glass Passivated Single Phase Bridge Rectifier

文件：372.08 Kbytes Page：4 Pages

Surface Mount Glass Passivated Single Phase Bridge Rectifier Reverse Voltage 1000V Ountput Current 2.0A

文件：259.029 Kbytes Page：4 Pages

Surface Mount Glass Passivated Single Phase Bridge Rectifier

文件：371.62 Kbytes Page：4 Pages

Surface Mount Glass Passivated Single Phase Bridge Rectifier Reverse Voltage 1400V Ountput Current 2.0A

文件：259.14 Kbytes Page：4 Pages

包装：托盘 描述：CONN SATA RCPT 22POS SLD R/A SMD 连接器，互连器件 插拔式连接器组件

包装：托盘 描述：CONN SATA PLUG 22POS SLD PCB 连接器，互连器件 插拔式连接器组件

Surface Mount Glass Passivated Single Phase Bridge Rectifier

文件：364.15 Kbytes Page：4 Pages

Surface Mount Glass Passivated Single Phase Bridge Rectifier Reverse Voltage 800V Ountput Current 2.5A

文件：258.25 Kbytes Page：4 Pages

Surface Mount Glass Passivated Single Phase Bridge Rectifier

文件：376.39 Kbytes Page：4 Pages

Surface Mount Glass Passivated Single Phase Bridge Rectifier

文件：364.13 Kbytes Page：4 Pages