Good vacuum pressure measurement for economical cost

文件：316.25 Kbytes Page：8 Pages

包装：散装 描述：BATTERY CONTACT SNAP 9V 电池产品 电池座，电池夹，电池触头

功能：LED 阵列 LOL 包装：盒 描述：KIT LED MATRIX LOL SHIELD RED A 开发板，套件，编程器 评估板 - 扩展板，子卡

Fork-type cable lug - C-FC 2,5/M6

Fork-type cable lug, non-insulated, 1.1 - 2.5 mm², M6

Ferrule - AI 1,0-8 RD S1

Taped ferrules, 1.0 mm², sleeve length 8 mm, with plastic collar, according to DIN 46228-4, red, for processing with the CRIMPFOX 4 IN 1, 10 strips each with 50 sleeves per strip.

Ferrule - AI 2,5-8 BU S1

Taped ferrules, 2.5 mm², sleeve length 8 mm, with plastic collar, according to DIN 46228-4, blue, for processing with the CRIMPFOX 4 IN 1, 10 strips each with 40 sleeves per strip.

Fork-type cable lug - C-FC 6/M4

Fork-type cable lug, non-insulated, 2.6 - 6 mm², M4

Fork-type cable lug - C-FC 2,5/M5

Fork-type cable lug, non-insulated, 1.1 - 2.5 mm², M5

Fork-type cable lug - C-FC 6/M4

Fork-type cable lug, non-insulated, 2.6 - 6 mm², M4

Fork-type cable lug - C-FC 2,5/M5

Fork-type cable lug, non-insulated, 1.1 - 2.5 mm², M5

Fork-type cable lug - C-FC 2,5/M6

Fork-type cable lug, non-insulated, 1.1 - 2.5 mm², M6

BOARD LEVEL POWER SEMICONDUCTOR HEAT SINKS

• No interface material is needed • Copper with matte tin plating for improved solderability and assembly • Both the component and the heat sink are installed on the PC-board utilizing standard SMT assembly equipment for ”Tape & Reel” and “Tube” formats • EIA standards and ESD protection are s

BOARD LEVEL POWER SEMICONDUCTOR HEAT SINKS

• No interface material is needed • Copper with matte tin plating for improved solderability and assembly • Both the component and the heat sink are installed on the PC-board utilizing standard SMT assembly equipment for ”Tape & Reel” and “Tube” formats • EIA standards and ESD protection are s

BOARD LEVEL POWER SEMICONDUCTOR HEAT SINKS

• No interface material is needed • Copper with matte tin plating for improved solderability and assembly • Both the component and the heat sink are installed on the PC-board utilizing standard SMT assembly equipment for ”Tape & Reel” and “Tube” formats • EIA standards and ESD protection are s

HIGH FREQUENCY MAGNETICS T1/E1 Through Hole Shielded Transformers

• Designed for DS1, DS1C, and CEPT applications • Electrostatic shield provides improved longitudinal signal suppression and EMI reduction • Maximum inductance unbalance of center-tapped windings is 0.1 • Operating temperature range: -40° C to +85° C • Meets IEC 695, 2-2 flammability r

HIGH FREQUENCY MAGNETICS T1/E1 Through Hole Shielded Transformers

• Designed for DS1, DS1C, and CEPT applications • Electrostatic shield provides improved longitudinal signal suppression and EMI reduction • Maximum inductance unbalance of center-tapped windings is 0.1 • Operating temperature range: -40° C to +85° C • Meets IEC 695, 2-2 flammability r

HIGH FREQUENCY MAGNETICS T1/E1 Through Hole Shielded Transformers

• Designed for DS1, DS1C, and CEPT applications • Electrostatic shield provides improved longitudinal signal suppression and EMI reduction • Maximum inductance unbalance of center-tapped windings is 0.1 • Operating temperature range: -40° C to +85° C • Meets IEC 695, 2-2 flammability r

HIGH FREQUENCY MAGNETICS T1/E1 Through Hole Shielded Transformers

• Designed for DS1, DS1C, and CEPT applications • Electrostatic shield provides improved longitudinal signal suppression and EMI reduction • Maximum inductance unbalance of center-tapped windings is 0.1 • Operating temperature range: -40° C to +85° C • Meets IEC 695, 2-2 flammability r

HIGH FREQUENCY MAGNETICS T1/E1 Through Hole Transformer

HIGH FREQUENCY MAGNETICS T1/E1 Through Hole Transformer • Operates at the DS1 rate of 1.544 Mbits/s • Provides high step-up ratio • Provides monitoring via winding (5-1) • Operating Temperature Range: -40° C to +85°C • Meets IEC 695, 2-2 flammability requirements • PWB Process Capability: St

HIGH FREQUENCY MAGNETICS T1/E1 Through Hole Hardened Transformer

HIGH FREQUENCY MAGNETICS T1/E1 Through Hole Hardened Transformer • Operating temperature range: -40° C to +85° C • Meets IEC 695, 2-2 flammability requirements • PWB Process Capability: standard printed wiring board assembly techniques, total-immersion cleaning • Reliability testing: shock, vi

HIGH FREQUENCY MAGNETICS T1/E1 Through Hole Shielded Transformers

• Designed for DS1, DS1C, and CEPT applications • Electrostatic shield provides improved longitudinal signal suppression and EMI reduction • Maximum inductance unbalance of center-tapped windings is 0.1 • Operating temperature range: -40° C to +85° C • Meets IEC 695, 2-2 flammability r

HIGH FREQUENCY MAGNETICS T1/E1 Through Hole Shielded Transformers

• Designed for DS1, DS1C, and CEPT applications • Electrostatic shield provides improved longitudinal signal suppression and EMI reduction • Maximum inductance unbalance of center-tapped windings is 0.1 • Operating temperature range: -40° C to +85° C • Meets IEC 695, 2-2 flammability r

HIGH FREQUENCY MAGNETICS T1/E1 Single Through Hole Shielded Transformers

• Designed for DS1, DS1C, and CEPT applications • Electrostatic shield provides improved longitudinal signal suppression and EMI reduction • Maximum inductance unbalance of center-tapped windings is 0.1 • Operating temperature range: -40° C to +85° C • Meets IEC 695, 2-2 flammability r

HIGH FREQUENCY MAGNETICS T1/E1 Through Hole Shielded Transformers

• Designed for DS1, DS1C, and CEPT applications • Electrostatic shield provides improved longitudinal signal suppression and EMI reduction • Maximum inductance unbalance of center-tapped windings is 0.1 • Operating temperature range: -40° C to +85° C • Meets IEC 695, 2-2 flammability r

HIGH FREQUENCY MAGNETICS T1/E1 Through Hole Shielded Transformers

• Designed for DS1, DS1C, and CEPT applications • Electrostatic shield provides improved longitudinal signal suppression and EMI reduction • Maximum inductance unbalance of center-tapped windings is 0.1 • Operating temperature range: -40° C to +85° C • Meets IEC 695, 2-2 flammability r

HIGH FREQUENCY MAGNETICS T1/E1 Single Through Hole Shielded Transformers

• Designed for DS1, DS1C, and CEPT applications • Electrostatic shield provides improved longitudinal signal suppression and EMI reduction • Maximum inductance unbalance of center-tapped windings is 0.1 • Operating temperature range: -40° C to +85° C • Meets IEC 695, 2-2 flammability r

HIGH FREQUENCY MAGNETICS T1/E1 Through Hole Shielded Transformer

HIGH FREQUENCY MAGNETICS T1/E1 Through Hole Shielded Transformer • Designed for DS1, DS1C, and CEPT applications • Electrostatic shield provides improved longitudinal signal suppression • 2741J has an internal connection to terminal 8; do not use • Operating temperature range: -40° C to +85° C

HIGH FREQUENCY MAGNETICS T1/E1 Through Hole Shielded Transformer

HIGH FREQUENCY MAGNETICS T1/E1 Through Hole Shielded Transformer • Designed for DS1, DS1C, and CEPT applications • Electrostatic shield provides improved longitudinal signal suppression • 2741J has an internal connection to terminal 8; do not use • Operating temperature range: -40° C to +85° C

HIGH FREQUENCY MAGNETICS Specialty Through Hole Shielded Transformer

HIGH FREQUENCY MAGNETICS Specialty Through Hole Shielded Transformer • Operates as a high frequency pulse transformer in telecom switching systems at various signaling rates • Interwinding Electrostatic Shield provides low capacitance and high EMI suppression • Electrical equivalents: 2664A and

HIGH FREQUENCY MAGNETICS T1/E1 Through Hole Shielded Transformers

• Operate at the T1 rate of 1.544 Mb/s and the E1 rate of 2.084 Mb/s • Interwinding Electrostatic Shield provides low capacitance and high EMI suppression • There is an internal connection to Terminal 8; do not use • Minimum interwinding breakdown voltage of 2200 Vdc • Operating temper

HIGH FREQUENCY MAGNETICS T1/E1 Through Hole Shielded Transformers

• Operate at the T1 rate of 1.544 Mb/s and the E1 rate of 2.084 Mb/s • Interwinding Electrostatic Shield provides low capacitance and high EMI suppression • There is an internal connection to Terminal 8; do not use • Minimum interwinding breakdown voltage of 2200 Vdc • Operating temper

SWITCH-MODE TRANSFORMER GUIDE

CONSUMER PRODUCTS Pulse offers a complete range of Switch-Mode Transformers in various technologies (slot, layer and triple insulation wire) used for power supplies in television, set-top boxes, satellite receivers, DVD players, telephone chargers, and white goods. Pulse also offers a new range o

CANopen / DeviceNet Data Double-Ended Cordset

Product Description CANopen / DeviceNet Data Double-Ended Cordset: Male straight A-coded black M12 Standard to female straight A-coded black M12 Standard, 50 V AC / 60 V DC, 4 A; PUR black cable, 4-wires, Data: 2x0.25 mm² + Power: 2x0.34 mm²

BOARD LEVEL POWER SEMICONDUCTOR HEAT SINKS

• No interface material is needed • Copper with matte tin plating for improved solderability and assembly • Both the component and the heat sink are installed on the PC-board utilizing standard SMT assembly equipment for ”Tape & Reel” and “Tube” formats • EIA standards and ESD protection are s

BOARD LEVEL POWER SEMICONDUCTOR HEAT SINKS

• No interface material is needed • Copper with matte tin plating for improved solderability and assembly • Both the component and the heat sink are installed on the PC-board utilizing standard SMT assembly equipment for ”Tape & Reel” and “Tube” formats • EIA standards and ESD protection are s

BOARD LEVEL POWER SEMICONDUCTOR HEAT SINKS

• No interface material is needed • Copper with matte tin plating for improved solderability and assembly • Both the component and the heat sink are installed on the PC-board utilizing standard SMT assembly equipment for ”Tape & Reel” and “Tube” formats • EIA standards and ESD protection are s

RF Power Field Effect Transistors

RF Power Field Effect Transistors N- Channel Enhancement- Mode Lateral MOSFETs Designed primarily for CW large- signal output and driver applications with frequencies up to 600 MHz. Devices are unmatched and are suitable for use in industrial, medical and scientific applications.

RF Power Field Effect Transistor

880 MHz, 10 W AVG., 28 V SINGLE N-CDMA LATERAL N-CHANNEL BROADBAND RF POWER MOSFET Designed for broadband commercial and industrial applications with frequencies up to 1000 MHz. The high gain and broadband performance of this device makes it ideal for large-signal, common-source amplifier applica

Airfast RF Power LDMOS Transistor

Airfast RF Power LDMOS Transistor

RF Power Field Effect Transistor

880 MHz, 10 W AVG., 28 V SINGLE N-CDMA LATERAL N-CHANNEL BROADBAND RF POWER MOSFET Designed for broadband commercial and industrial applications with frequencies up to 1000 MHz. The high gain and broadband performance of this device makes it ideal for large-signal, common-source amplifier applica

RF Power Field Effect Transistor N--Channel Enhancement--Mode Lateral MOSFET

2--500 MHz, 600 W, 50 V LATERAL N--CHANNEL BROADBAND RF POWER MOSFET Designed primarily for wideband applications with frequencies up to 500 MHz. Device is unmatched and is suitable for use in broadcast applications. • Typical DVB--T OFDM Performance: VDD = 50 Volts, IDQ = 2600 mA, Pout = 125 Wa

RF Power Field Effect Transistors

RF Power Field Effect Transistors N- Channel Enhancement- Mode Lateral MOSFETs Designed primarily for CW large- signal output and driver applications with frequencies up to 600 MHz. Devices are unmatched and are suitable for use in industrial, medical and scientific applications.

BOARD LEVEL POWER SEMICONDUCTOR HEAT SINKS

• No interface material is needed • Copper with matte tin plating for improved solderability and assembly • Both the component and the heat sink are installed on the PC-board utilizing standard SMT assembly equipment for ”Tape & Reel” and “Tube” formats • EIA standards and ESD protection are s

BOARD LEVEL POWER SEMICONDUCTOR HEAT SINKS

• No interface material is needed • Copper with matte tin plating for improved solderability and assembly • Both the component and the heat sink are installed on the PC-board utilizing standard SMT assembly equipment for ”Tape & Reel” and “Tube” formats • EIA standards and ESD protection are s

BOARD LEVEL POWER SEMICONDUCTOR HEAT SINKS

• No interface material is needed • Copper with matte tin plating for improved solderability and assembly • Both the component and the heat sink are installed on the PC-board utilizing standard SMT assembly equipment for ”Tape & Reel” and “Tube” formats • EIA standards and ESD protection are s

End cutting nippers Professional ESD

Round-nose pliers Professional ESD Needle nose pliers Professional ESD Flat-nose pliers Professional ESD Needle nose pliers Professional ESD

High Voltage (Plate) & Filament - 32 VA to 454 VA

Features Primary 115 VAC, 60 Hz. - except as noted For universal primaries and/or 50/60 Hz. operation and other output voltagecombinations please see our 300 Series Enclosed, 4 hole, chassis mount. Minimum 6 long leads. Units can be run full wave bridge or full wave C.T. Class A insulation (

High Voltage (Plate) & Filament - 32 VA to 454 VA

Features Primary 115 VAC, 60 Hz. - except as noted For universal primaries and/or 50/60 Hz. operation and other output voltagecombinations please see our 300 Series Enclosed, 4 hole, chassis mount. Minimum 6 long leads. Units can be run full wave bridge or full wave C.T. Class A insulation (

High Voltage (Plate) & Filament - 32 VA to 454 VA

Features Primary 115 VAC, 60 Hz. - except as noted For universal primaries and/or 50/60 Hz. operation and other output voltagecombinations please see our 300 Series Enclosed, 4 hole, chassis mount. Minimum 6 long leads. Units can be run full wave bridge or full wave C.T. Class A insulation (

Lowpass Filter

文件：57.26 Kbytes Page：2 Pages

Dome Plugs

文件：105.62 Kbytes Page：1 Pages

ADSL TRANSFORMER

文件：46.42 Kbytes Page：1 Pages

ADSL TRANSFORMER

文件：46.42 Kbytes Page：1 Pages

ADSL TRANSFORMER

文件：46.42 Kbytes Page：1 Pages

Shrink sleeve - MM-WMS-2 4,8 (EX9)R C1 WH/BK

文件：172.08 Kbytes Page：3 Pages

ATTB 6 BL

文件：266.41 Kbytes Page：4 Pages

Shrink sleeve - MM-WMS-2 4,8 (EX9)R C1 WH/BK

文件：172.08 Kbytes Page：3 Pages

Tool set - CRIMPSET 6

文件：78.95 Kbytes Page：5 Pages

Ferrule - AI 1,5 -12 BK -1000

文件：57.36 Kbytes Page：3 Pages

Television Chroma System

Integrated Circuit TV Chroma IF Amp